endo-cart
18Pages

THE SPECIALIST WHERE LOTS OF SPACE IS NEEDED endo-cart was designed especially to meet the special challenges in operating theatres. This is where every second counts and each movement must be correct. Particularly in the case of ERCP investigations Diagnostic endoscopy and Surgical endoscopy endo-cart impresses with the high level of stability, functional perfection, exceptional load rating and comprehensive technical equipment.

Technical data Order configurations endo-cart

endo-cart – The Highlights At a Glance Space can be saved by installing accessories along a standard runner located between the extended vertical extrusions. The middle column, which joins the top shelf to the lower set of shelves, ensures additional stability. Perfect functionality The rugged basic frame can bear a payload of up to 150 kg / 330 lbs. With an overall width of 1100 mm the endo-cart affords ample space for bulky medical equipment. Depending on the size of the medical equipment it must carry, the endo-cart is available in two widths: Symmetrically distributed cart width: 500 mm...

endo-cart – IMPRESSIVE ON ACCOUNT OF ITS SPACIOUSNESS AND WIRING Unique traits of the two-column endo-cart model is the ample storage space it provides and its outstanding stability. Its features can be summarised under the following headings: 1 Ample room for medical equipment up to 1100 mm in length. Individual components can be installed e.g. a shelf or drawers (that can be labelled with markers), thanks to the symmetrical distribution of the cart’s width. 3 T-slots with tapped strips along the (lengthened) vertical sections enable attachment of numerous additional components, such as...

The top of the cart provides a storage space 1100 mm in length. In cross-section: The power column of the mobile carrier system endo-cart. 117

design elements and dimensions Socket strip for assembly in the power column Power column (made of extruded aluminium) Cap of the vertical extrusion (made of plastic (ABS)) Cap of the vertical extrusion (made of plastic (ABS)) with hole (Ø 25 mm), is used with accessories in the guide Decorative trim (made of sheet steel), in RAL 5021 (water blue), RAL 5013 (cobalt blue) or RAL 7035 (light grey), powder-coated Tapped strip (made of steel) for mounting all system components in the cart interior (tapped holes M6 in increments of 32 mm) Cap of the power column (made of plastic (ABS)) Vertical...

Basic version Basic version (with extended vertical extrusions) Installation height Total height TH for H (in units) castors Ø 100 mm Total height TH for castors Ø 125 mm Setup basic frame Load capacities 1 base 4 twin swivel castors, lockable, Ø 100 mm or Ø 125 mm (optionally also supplied in conductive version) 2 vertical extrusions each with 2 tapped strips (in increments of 32 mm) 2 power columns (for use as cable ducts and for mounting socket strips) 1 centre column (as additional cable duct and for mounting the system components) Supplied fully assembled Basic frame (total payload)...

MODULARITY FOR NUMEROUS CONFIGURATION OPTIONS The modular structure is the defining feature of the endo-cart mobile two-column equipment carts and the entire ITD product range, which allows all support systems to be configured, customised, upgraded or easily modified for special functions and application areas using the extensive standard range. This capability allows users to react fast and consistently to any changes or new customer requirements. The T-slots on the support extrusion or special devices ensure easy assembly of the components. The display presented alongside shows a small...

Medical consumer material can be stored transparently in multipurpose boxes. Endoscope holders can be accommodated in the vertical extrusions or attached to the shelf with two mounts. A range of accessories, such as foot switch cradle can be easily attached to the equipment cart. Overview system components and accessories

order configurations endo-cart basic version Order number: EC.0410.XXX 2) Equipment cart, 30 U 1) (total height: 1117 mm), fitted with: 1 basic frame (see page 148) with 4 twin swivel castors, lockable, Ø 100 mm, conductive 2 vertical extrusions each with 2 tapped strips 2 power columns as mounting for socket strip and cables 1 centre column as additional cable duct 2 decorative trims 1 continuous upper platform (width: 1100 mm) with a handle left and right 1 block of drawers, 3 units 4 shelves 1 shelf, pull-out 1 multipurpose box (5 boxes) 1 endoscope holder, single 1 drain glas 1 socket...

endo-cart basic version (with extended vertikal extrusions) Order number: EC.0416.XXX 2) Equipment cart, 30 U + 10 U 1) (total height: 1465 mm), fitted with: 1 basic frame (see page 149) with 4 twin swivel castors, lockable, Ø 125 mm, conductive 2 vertical extrusions each with 2 tapped strips 2 power columns as mounting for socket strip and cables 1 centre column as additional cable duct 2 decorative trims 1 continuous upper platform (width: 1100 mm) with a handle left and right 1 standard runner for mounting accessories (length: 1100 mm) 3 blocks of drawers, 1 unit 4 shelves 1 shelf,...

overview System components And accessories Basic frame symmetrical width division, 500 mm / 500 mm asymmetrical width division, 450 mm / 600 mm asymmetrical width division, 600 mm / 450 mm Basic frame with extended vertikal extrusions symmetrical width division, 500 mm / 500 mm asymmetrical width division, 450 mm / 600 mm asymmetrical width division, 600 mm / 450 mm Rear panel symmetrical width division, 500 mm / 500 mm asymmetrical width division, 450 mm / 600 mm Ø 125 mm, conductive, instead of standard Ø 100 mm, conductive wall protector Installation width without handle with handle with...

Connection holder accommodates up to three endoscope connectors Rinsing bottle holder Hose holder Camera holder with clamp cable holder Bottle holder for gas bottles with max. 2 l content for gas bottles with 3 / 5 / 10 l content, max. Ø 145 mm for gas bottles with max. 20 l content, max. Ø 205 mm 4-arm, with one-hand adjustment, 4 x 2 kg / 4 x 4.4 lbs 4-arm, with one-hand adjustment, 4 x 5 kg / 4 x 11 lbs Standard runner rigid on rotation unit for standard runner, Ø 16 mm for standard runner, Ø 18 mm for shelf, Ø 16 mm for shelf, Ø 18 mm Rail fastener Holder for suction system...