Surgical Kit
1 / 11ページ

INNO SUB. KCA010F FULL SURGICAL KIT

INNO SUB. FULL SURGICAL KIT [KCA010F] SUB. HEXAGON SYSTEM INNO INT. FULL SURGICAL KIT [KCA010FI] INT. OCTAGON SYSTEM > For INNO Submerged Implant System (Sub.). > All components are for Sub. / Int. / Ext. except for the Fixture Drivers and the Depth Gauge used for Sub. exclusively. Ø3.5 Fixture Final Drill Path Drill Drill Extension Ø4.5 Fixture Final Drill Ø5.0 Fixture Final Drill Ø6.0 Fixture Final Drill Drill Extension An exclusive tool by type Depth Gauge Torque Wrench Ø4.0 Fixture Final Drill Torque Wrench Ø3.5 Fixture Final Drill Ø6.0 Fixture Final Drill Ø5.0 Fixture Final Drill Ø4.5...

INNO EXT. FULL SURGICAL KIT EXT. HEXAGON SYSTEM > For the selection and use guide of the components for the Sub. Int. & Ext. Full Surgical Kit, refer to pages 005 to 011. > For the INNO External Implant System (Ext.). > All components are for Sub. / Int. / Ext. except for the Fixture Drivers and the Multi Countersink used for Ext. exclusively. Drill / Surgical Tool Point Drill > Primarily used for marking the implant recipient site and to determine spacing. > The point drill has a unique pointed tip, making this an excellent drill for starting the osteotomy through the hard cortical plate....

> Used in preparation of osteotomy in dense bone only. *Extra product *Extra product > Bone quality 1 : high compressive placement of fixtures induces the failure of osseointegration > Insert the Parallel Pin after Ø2.2 or 3.5 Drill to check the osteotomy path. > In order to prevent losing Parallel Pin in patient’s mouth, be sure to tie floss through the hole > Countersink decreases torque force (Ø4.0 Fixture : 80 N.cm -> 45 N.cm / Ø5.0 Fixture : 150 N.cm -> 45 N.cm). > Preventing compressive necrosis of dense cortical bone. After Ø3.5 final drilling. Upper margin of depth marking line...

Mount Driver Fixture Driver > Used to install Pre-Mount type fixtures. > Used to install No-Mount type fixtures. *Extra product *Extra product Type Sub. > Used to insert or remove the Cover Screw, Healing Abutment and Abutment Screw etc. > The Machine Drivers are used with contra angle, while the Ratchet Drivers are used with the Torque Wrench. H Torque Wrench *Extra product > Torque control in implant placement and abutment connection. > Torque force 10, 25, 30 & 35 N.cm are able to be controlled by pulling the elastic bar. > Maximal torque force 120 N.cm with pulling the rigid main bar....

※ Sloped edentulous ridge adjacent of tooth Drilling Sequence > Minimal drill frequency with the Point Drill, Initial Drill and Final Drills > Crestal cutter of the Initial Drill and Final Drill. > Longer drills than fixture’s length. (Ø3.5, Ø4.0 and Ø4.5 Fixtures). Initial Drill Final Drill Crestal flatting Longer Final Drill ※ Wide extraction socket > Absence of the cortical bone & spongy bone. > Narrower diameter than the fixture’s diameter. Ø4.0 Drill Initial Drill Actual length of Drill : Fixture + 1mm ※ Torque force control > The 0.5mm deeper placement increases the initial torque...

INNO SUB. SMART SURGICAL KIT [KSA002] SUB. HEXAGON SYSTEM Length Marking & Stopper > For the INNO Submerged Implant System (Sub. Ø3.5, 4.0, 4.5 & 5.0). > A simpler kit for implant surgery, applied to fixtures with 8~14mm in length using the Drills and Stoppers. Actual Length of Drill : Fixture length + 1mm Diameter band * While the 2.2 Initial Drill is used at 1,000 rpm with irrigation, the Final Drills from the 3.5 to 5.0 should be used at 50 rpm without irrigation. Drilling Sequence Drill Countersink Hard Bone Normal Bone Hard Bone Countersink Hard Bone Hard Bone Normal Bone Initial Drill...

INNO SUB-SHORT SURGICAL KIT [KSI001] > For the INNO Submerged Short Implant System (Sub.). Actual length of drill : Fixture + 0.5mm. Diameter band Length Marking & Stopper Drilling Sequence Normal Bone Point A common tool for the INNO Surgical Kits. Hard Bone An exclusive tool for the Short Implants. Normal Bone Hard Bone A common tool for the INNO Surgical Kits. Point Drill An exclusive tool for the Short Implants. Normal Bone Hard Bone A common tool for the INNO Surgical Kits. An exclusive tool for the Short Implants. Normal Bone Extension & Driver Hard Bone A common tool for the INNO...

INNO SUB-NARROW SURGICAL KIT [KNA001] SUB-N. HEXAGON SYSTEM > For the INNO Submerged Narrow Implant System (Sub-N). Ratchet X-Long Machine X-Long Drill Stopper Fixture Driver Mount Driver Type Parallel Pin Countersink Ratchet Long *Extra product > Used to install fixture. Spare Point Depth Gauge Torque Wrench Point Drill After Ø3.1 / Ø3.3 Drilling. Cuff Height Countersink Normal Bone Drilling Sequence Hard Bone Extension & Driver Normal Bone Hard Bone Depth Gauge Fixture Driver(Ratchet) Fixture Driver(Machine)

COWELL® PROSTHETIC KIT [KPA003] SUB. HEXAGON SYSTEM > For the INNO Submerged Implant System. > Try-in Kit for determining abutment specifications. ® Abutment Gauge > Measuring of the diameter, cuff length and angulation of abutment. 7 5.5 4 Straight Type Angulated Type Abutment Driver > Used in the Shoulder, Solid, Absolute, and Straight Abutment placement. Trephine soft tissue over the Cover Screw of fixture.

Cowellmedi Co.,Ltd Floor 6, Blue Fin Tower, 42, Seochojungang-ro,Seocho-gu, Seoul, Korea Tel. +82-2-3453-5085 Fax. +82-2-3453-5086 E-mail. cib@cowellmedi.com Cowellmedi USA INC 218 Trianon LN Villanova PA 19085-1442 USA Tel. 1-623-939-1344 Fax. 1-623-939-1472 Cowell R&D Institute 48, Hakgam-daero 221beon-gil, Sasang-gu, Busan, 46986, Korea Tel. +82-51-314-2028 Fax. +82-51-314-2026