tztG_EN
1 / 12ページ

Erkodent thermoforming units 2015

thermoforming unit with automated thermoforming process 1 Program foil 2 Insert foil 3 Start heating process, latest now place model in the unit 4 Time for other, everything else will be carried out by the Erkoform-3d motion! The thermoforming process and cooling time run automatically. The automatic is limited to the really expedient working step, namely the actual thermoforming process. This saves the necessary going to the unit in order to move the hot foil from the heating to the model and to thermoform. • No compressed-air supply required - plug and play. • • Touchless temperature...

The Erkoform-3dmotion is the quintessence of the Erkodent vacuum units. All characteristics of the proven and continuously improved Erkoform-3d (3d+) are available plus an unmatched operating comfort by the automated thermoforming process. An example, you would like to fabricate a splint without adjustment of the opposing bite: Select foil at the touchpanel ››› insert foil ››› turn foil under the heating ››› place model ... everything else, heating, thermoforming and cooling will be carried out by the unit. You decide when you will go back to the unit. No overheating, no forgetting, no...

Erkoform-3d + thermoforming unit with reserve-vacuum and touchpanel • Same characteristics as the Erkoform-3dmotion but without automated thermoforming process. Touchpanel (Erkoform-3dmotion and 3d+ with different functions) Special functions allow to separately turn the heating and vacuum pump on and off. Safety switch-off after 10 sec. when the next working steps are not executed. Many different languages can be selected. The program contains all Erkodent thermoforming materials, leads as short guide with animations through the sequence of work and indicates the required working steps....

The Erkoform-3d+ is a noticeable further development of the Erkoform-3d. It is technically an Erkoform-3dmotion without automatic. technical data see last page Both units are characterized by a sudden adaptation. This is possible because of a provided large volume reserve vacuum. Both units use a sensor for a touchless temperature measurement of the thermoforming material. This guarantees the exact material temperature for the thermoforming process independent of the surroundings. Both units are equipped with a medium-wave infrared heating without preheating time. By the medium-wave heating...

Erkopress 300 Tp • Erkopress 300 Tp-ci pressure forming units for all applications in dental thermoforming technique The working pressure of the Erkopress 300 Tp unit can be set from 3 - 6 bar. The Erkopress 300 Tp-ci builds up a pressure of 7 bar in a reserve pressure chamber after turning the unit on and holds this pressure independently of the program sequence. For the adaptation 6 bar will then be available. The Erkopress 300 Tp unit will be connected to the available compressed-air system. The Erkopress 300 Tp-ci unit owns an integrated powerful compressor with reserve compressed-air....

Both units are characterized by a sudden adaptation. For equal wall thicknesses the hot thermoforming material will be vertically driven onto the model. At the same time the cylinder will be extended and the adaptation effected without delay. technical data see last page Both units use a sensor for a touchless temperature measurement of the thermoforming material and are equipped with the medium-wave infrared heating without preheating time described at page 4. With the accessory Tp-polymerisation pot 171 888 (pictures to the right) both units can also be used as pressure pot for...

Occluform-3 Occluform-3 is a unique occludator for the Erkoform units of the serie 3 Since the dimensions of the Occluform-3 correspond to those of a modern semi-adjustable articulator the device allows a bite elevation according to average values. If a construction bite taken in the mouth or in a fully adjustable articulator is available this will be used to articulate the models in the Occluform-3. One marking line at the supporting pin corresponds to approx. 1 mm bite elevation at the incisal point. • Plaster free model fixation. • Much space also for higher models. • Single column...

If the upper jaw model is fixed in the model pot the upper joint of the joint column is blocked using the swing bolt. If the lower jaw model is fixed in the model pot the lower joint is blocked. This way the imprint of the opposing bite corresponds to the proportions of an articulator. To articulate the models the arresting joint has to be freely movable. Thereby the supporting pin has to be adjusted to the thicker 0-marking line. If necessary, lift the bite at the supporting pin and open the Occluform-3. Thermoform the foil and close the Occluform-3 directly after the adaptation until the...

compressed-air supply required touchless temperature sensor medium-wave infrared heater preheating time reserve vacuum or reserve pressure foil thicknesses from 0 to 5.5 mm vertical prestretching and adaptation adaptation without delay adjustment with Occluform-3 adjustable adaptation power touchpanel all program features Erkoform-3dmotion • Erkoform-3d + • Erkopress 300 Tp • Erkopress 300 Tp-ci no yes yes no yes yes yes yes yes no yes yes

H 31.5/W 35/D 37 cm foil Ø 120 mm foil thickness 0 - 5.5 mm weight 11.9 kg ~230/240/110/115 volts 360 watt max. vacuum 0.8 bar noise level < 70 dB(A) H 31.5/W 35/D 37 cm foil Ø 120 mm foil thickness 0 - 5.5 mm weight 13.9 kg ~230/240/110/115 volts 360 watt max. vacuum 0.8 bar noise level < 70 dB(A) H 32/W 33/D 43 cm foil Ø 120 mm foil thickness 0 - 5.5 mm weight 16.7 kg ~230/240/110/115 volts 360 watt working pressure 3 - 6 bar noise level < 70 dB(A) H 32/W 33/D 51 cm foil Ø 120 mm foil thickness 0 - 5.5 mm weight 20.9 kg ~230/240/110/115 volts 360 watt working pressure 6 bar noise level <...