TA6 Series
1 / 10ページ

Product Segments • Comfort Motion TiMOTION's TA6 series linear actuator is designed for lift applications like recliners, lifting chairs and movie theater seating. Its right angle design reduces noise and allows for fitment into most applications. Industry certifications for the TA6 linear actuator include EMC and RoHS. In addition, the TA6 is available with optional Hall sensors for position feedback. It can also be used where freewheeling push only functionality is desired. General Features Voltage of motor Maximum load Maximum load Maximum speed at full load Stroke Minimum installation dimension Color Certificate Operational temperature range Options 12, 24 or 36V DC 6,000N in push 4,000N in pull 23.4mm/s (with 1000N in a push or pull condition) > 25~1000mm > Stroke + 163mm Black UL962, EMC +5°C~+45°C Freewheeling push only, safety nut, Hall sensors

Standard Dimensions

Push Pull Self Locking Force (N) Typical Current (A) No Load With Load Typical Speed (mm/s) No Load With Load Note 1 Please refer to the approved drawing for the final authentic value. 2 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 3 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC. With a 36V DC motor, the current is approximately two-thirds the current measured in 24V DC....

Performance Data (24V DC Motor) Motor Speed (2600RPM, Duty Cycle 10%)

Performance Data (24V DC Motor) Motor Speed (3400RPM, Duty Cycle 10%)

Motor Speed (3800RPM, Duty Cycle 10%) Speed vs. Load 40.0 35.0 30.0 Performance Data (24V DC Motor)

Load and Speed See page 3 Retracted Length (mm) See page 8 Rear Attachment (mm) See page 9 Front Attachment (mm) See page 9 1 = Plastic, U clevis, slot 6.1, hole 10.2 1 = Punched hole on inner tube + plastic cap, without slot, hole 10.2, with plastic bushing 2 = Punched hole on inner tube + plastic cap, without slot, hole 12.2 3 = Plastic, U clevis, slot 8.2, depth 20.2, hole 10.2, for load push < 4000N & pull < 2500N 4 = Plastic, U clevis, slot 8.2, depth 20.2, hole 12.2, for load push < 4000N & pull < 2500N 5 = Punched hole on inner tube, without slot, hole 10.2, with plastic bushing 6 =...

C. Front Attachment V.S Special Function Front Spindle Function B. Load V.S. Stroke Stroke (mm) Load (N)

TA6 Ordering Key Appendix Rear Attachment (mm) 1 = clevis plastic, slot 6.1, hole U 10.2 24.5 4 = lastic, U clevis, slot 8.2, depth P 20.2, hole 12.2, for load push < 4000N & pull < 2500N 3 = Plastic, U clevis, slot 8.2, depth 20.2, hole 10.2, for load push < 4000N & pull < 2500N 2 = unched hole on inner tube + P plastic cap, without slot, hole 12.2 1 = unched hole on inner tube + P plastic cap, without slot, hole 10.2, with plastic bushing 8 = Aluminum casting, U clevis, slot 7 = luminum casting, U clevis, slot A 6.2, depth 17.0, hole 10.2 6 = unched hole on inner tube, P without slot,...

TA6 Ordering Key AppendixFunctions for Limit SwitchesWire Definitions CODE Pin 1 (Green) 2 (Red) O 3 (White) 4 (Black) 5 (Yellow) A (Blue) 1 extend (VDC+) N/A N/A N/A retract (VDC+) N/A 2 extend (VDC+) N/A middle switch pin B middle switch pin A retract (VDC+) N/A 3 extend (VDC+) common upper limit switch N/A retract (VDC+) lower limit switch 4 extend (VDC+) common upper limit switch medium limit switch retract (VDC+) lower limit switch 1 = DIN 6P, 90° plug 2 = Tinned leads Cable length for direct cut system (mm) L3 100 400 500 100 1000 1000 1200 The user is responsible for determining the...