TGM1 series
1 / 7ページ

{{requestButtons}}

カタログの抜粋

TGM1 series - 1

TGM1series Product Segments • Ergo Motion • Industrial Motion TiMOTION's TGM1 series gear motor was designed primarily for ergonomic applications like height adjustable workstations and tables, but can be used in many other applications. This economical product allows for fast, smooth and quiet adjustment of built-in spindles through the use of external limit switches. Shafting allows for the mechanical synchronization of dual spindles. General Features 24V DC or 24V DC (PTC) 144RPM (±5%) after gear reduction 7.4Nm UL962 +5°C~+45°C Voltage of motor Maximum speed at full load Maximum rated torque Certificate Operational temperature range at full performance Options Hall sensors Hexagon hole for the shaft by 6mm diameter Low noise

カタログの1ページ目を開く
TGM1 series - 2

Standard Dimensions -Without TES2 (mm) Standard Dimensions With TES2 (mm) Self Locking Force (Nm) Typical Current (A) Typical Speed (RPM, ±5%) Hall Sensor Output No Load With Load No Load With Load Magnet Period (ms) No Load With Load Note 1 Please refer to the approved drawing for the final authentic value. 2 The current & speed in table and diagram are tested with TiMOTION control boxes, and there will be around 10% tolerance depending on different models of the control box. (Under no load condition, the voltage is around 32V DC. At rated load, the voltage output will be around 24V DC)

カタログの2ページ目を開く
TGM1 series - 3

Motor Speed (3800RPM) Speed vs. Torque Load 400 Current vs. Torque Load 10.0 Performance Data (24V DC Motor)

カタログの3ページ目を開く
TGM1 series - 4

Motor Speed (3400RPM) Speed vs. Torque Load 400 Current vs. Torque Load 10.0 Performance Data (24V DC Motor)

カタログの4ページ目を開く
TGM1 series - 5

Performance Data (24V DC Motor) Speed vs. Torque Load Current vs. Torque Load

カタログの5ページ目を開く
TGM1 series - 6

0 = Without 2 = Hall sensor * 2 0 = Without 1 = Motor brake 0 = Tinned leads 1 = DIN 6P, 90° 2 = Molex 8P 0 = Straight, 1000 1 = Straight, 1500 2 = Straight, 2000 3 = Curly, 1000 1 = Drive shaft hole (inner hexagon 9) 5 = Drive shaft hole (inner hexagon 6) 00 = Without XX = Number of output rotations (between13~17 & 25~35 rotations, factory preset)

カタログの6ページ目を開く
TGM1 series - 7

1 = DIN 6P, 90° plug 2 = MOLEX 8P, plug 50 Note 1 The combinations of TGM and TBS are marked as "v" on the above table. 2 When choosing the combination of TBS2 / 3 and TGM7, the hexagonal drive shaft is not required. 3 When choosing the combination of TBS1 / 4 / 5 / 9 / 10 and TGM1 / 3 / 4, the extra order of hexagonal drive shaft is needed. 4 Please refer to the table below for the serial numbers and the dimensions of the component. Hexagonal drive shaft The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to...

カタログの7ページ目を開く

TiMOTION Technology のすべてのカタログと技術パンフレット

  1. ERGO MOTION

    48 ページ

  2. CARE MOTION

    32 ページ

  3. series TL3

    12 ページ

  4. JP4 series

    7 ページ

  5. TA41 series

    11 ページ

  6. JP3 series

    7 ページ

  7. TA6 Series

    10 ページ

  8. TA1 Series

    12 ページ

  9. TGM3 Series

    6 ページ

  10. TGM2 Series

    7 ページ