ULM CASE II
1 / 16ページ

ULM CASE II Emergency Case

WEINMANN : HAMBURG Cover plate Long top divider (246,5 mm) Short top divider (105 mm) Case top Top recess Case hinge Short base divider (121 mm) Retaining clamps Oxygen cylinder recess Bottom recess Base of case Corner of case Case fastener Case handle Long base divider (211 mm) Seal Medium base divider (147 mm) 18 Tube holder a) Oropharyngeal tube, small b) Oropharyngeal tube, large 19 Lock 20 Set of 2 clamp straps for oxygen cylinder 21 Laryngoscope pouch 22 Ampoule strip 23 Ampoule panel

1.1 Special markings on the device WEINMANN : HAMBURG WEINMANN : HAMBURG WEINMANN : HAMBURG Meaning Device ID plate ULM CASE II

2 Description 2.1 Intended purpose The ULM CASE II Emergency Medical Case is designed for storage and transport of emergency medical apparatus, instruments, drugs and other items. 2.2 Function The interior of the ULM CASE II can be subdivided to suit individual requirements using the variable dividers. Accessories, such as ampoule strips, ampoule panels, tube holders and oxygen cylinder clamp straps, offer further possibilities for individual outfitting. 3 Safety Instructions Please note the following for your own safety and that of your patients: • Please comply with these User‘s Manual....

accessories nor genuine replacement parts recommended in the instructions for use are used. E nsure that spilled liquids, e.g. from ampoules, are removed immediately, otherwise they could destroy the backpack and injure the user. In this respect, comply with the warning and disposal instructions from the manufacturer concerned. Comply with Section “5 Hygienic preparation” on page 9 to prevent infection or bacterial contamination. When the backpack is equipped with oxygen cylinders and other equipment, it is essential to comply with the relevant instructions for use and the special...

4 Use 4.1 Dividers The case can be divided internally as required using the dividers (7, 15 and 17). An example is shown in Legend. When fitting the dividers, please ensure that: • hey are positioned correctly as t • hey are fitted perpendicularly into opposing t grooves • the spring fittings are properly engaged. To remove a divider, press the two circular spring fittings inwards as shown and lift the divider upwards. To change the position of the ”top long” divider (2) in the case top, first remove the cover plate above the divider. Bend the cover plate until the corners of the plate slip...

4.2 Tube Holder When the case is supplied, the tube holders are attached to the “medium base” divider (17). The tube holder can be moved to another divider in the base of the case by loosening the fixings and relocating the holder as required. W 4.3 Ampoule Strips The ”ampoule strips WM 15140” (22), which are available as accessories, can be fitted as required to the underside of the cover plates as shwon. Make sure that the dividers or other fittings do not catch on any of the ampoules when the plates are closed. 4.4 Ampoule Panels The “ampoule panels WM 8771” (23), available as...

4.5 Cylinder Clamp Straps To fit 0.8 l or 2.0 l oxygen cylinders in the base of the case, use the accessory ”WM 15141 – set of 2 clamp straps for oxygen cylinders” (20). The cylinders are fitted in the oxygen cylinder recess as shown. To secure a 2.0 l cylinder, use the outer clamps. The centre and lefthand clamps are used for an 0.8 l cylinder. Ensure that the straps are tight to prevent the cylinder from slipping during transport. 5 Hygienic preparation Clean the inside and outside of the case simply by wiping with disinfectant. Recommended disinfectant: • terralin® protect. See also the...

6 Functional Control Carry out a functional control after every use(or at least every 2 years if not used). If you discover faults during the functional control, you must not use the emergency case again until the faults have been rectified. Carry out the functional control as follows: 1. Check whether the inserts,cover plate, ampoule strips, corners of the case and the case handle are free from damage. 2. Check that the case fasteners can be opened and closed easily. 3. Check the case and cover plate hinges. They must move easily and be fixed in place correctly. Replace faulty parts. 7...

E mergency or by technicians authorized by W EINMANN Emergency, and the sender charged for this. ⇒ Clean and disinfect parts required for maintenance work. ⇒ Do not send in parts which are potentially contaminated. 1. Remove parts 2. Clean and disinfect parts (“5 Hygienic preparation” on page 9). 3. Send parts to WEINMANN Emergency, or to a technician specifically authorized by WEINMANN Emergency. Do not dispose of the therapy device in domestic waste. To dispose of the therapy device properly, contact an approved, certified electronics scrap dealer. You can obtain the address from your...

8.2 Accessories and Spare Parts Standard symbol labels: Oxygen Put on protective gloves Dressing box Syringes ECG Intubation Infusion CIRCULATION drugs RESPIRATION drugs Universal drugs Resuscitation Baby resuscitation Cannula Tubes Clamps Poison Infant, red Infant, green Wall mount Base divider, long (211 mm) Base divider, medium (147 mm) Base divider, short (121 mm) Top divider, long (246,5 mm) Top divider, short (105 mm) Cover plate, assembled Ampoule panel Laryngoscope pouch Ampoule panel without ampoule strips Ampoule strip* Set of 2 oxygen cylinder clamp straps Holder for...

Holder for oropharyngeal tubes, large* (for adults, juveniles and children) Lock Case handle* Journal pins, set of 2* Seal, set of 2* Ampoule strip, set of 3 To replace the following fittings, the rivets of the parts needing replaced have to be bored out. Blank rivert tongs will be required. Case corner, set of 4* Case support, set of 2* Case hinge, set of 3* Case fastener, set of 2* Retaining clamp, set of 6* To change the following inserts, the entire case shell has to be dismatied. This involves boring out the rivets from all fittings such as fasteners, hinges, etc. and fitting new...