User’s Instruction
2Pages

User’s Instruction READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE PPE Keep this note for as long as the Personal Protective Equipment (PPE) remains in use, complying scrupulously with its content. If you should have doubts as to the degree of protection offered by the footwear, its use and maintenance after reading this notice, please contact the safety manager before using it. If you have any further requirements or require more information, please contact CLEMENT DESIGN. This pair of shoes is intended to provide personal protection to its user. It was made using high tech materials. It’s equipped with non-slip rubber soles (technology SSR®). The mark on this product means that it meets the essential requirements provided by the European Regulation (EU) 2016/425 regarding PPE. It is designed and manufactured in accordance with the following European standards (See footwear marking) Or Personal protective equipment - Safety Footwear Personal protective equipment - Occupational Footwear EU type- examination certificate issued by notified body (See EU declaration of conformity on www.clementdesign.com website) Or C.T.C. A.N.C.I. Servizi srl Sezione CIMAC c/so VIPO a.s. Parc Tony Garnier, 4, rue Hermann Frenkel, 69367 Lyon Cedex 07, France Corso G. Brodolini, 19 27029 VIGEVANO (PV), Italy Gen. Svobodu 1069/4, 958 01 Partizánske, Slovakia Safety Footwear Occupational Footwear Footwear incorporating protective features to protect the wearer from injuries which could arise through accidents EN ISO 20345:2011 EN ISO 20347:2012 Items of safety footwear are fitted with toecaps designed to give protection against impact when tested at an Not equipped with protection toecaps energy level of at least 200 J and against compression when tested at a compression load of at least 15 kN. SB / S1 / S2 / S3 / S4 / S5 or SBH OB / O1 / O2 / O3 / O4 / O5 or OBH SB = Basic requirements - Class I OB = Basic requirements - Class I S1 = SB + A + E + FO + Closed seat region O1 = OB + A + E + Closed seat region S2 = S1 + WRU O2 = O1 + WRU S3 = S2 + P + Cleated outsole O3 = O2 + P + Cleated outsole SB = Basic requirements - Class II OB = Basic requirements - Class II S4 = SB + Closed seat region + A + E + FO O4 = OB + Closed seat region + A + E S5 = S4 + P + Cleated outsole O5 = O4 + P + Cleated outsole SBH = Some basic requirements OBH = Some basic requirements of class I and class II of class I and class II Definitions & meanings of markings (See footwear marking) European Standards Category Meaning for leather footwear & other materials, excluding all-rubber or all-polymeric footwear Class I Meaning for All-rubber (i.e. entirely vulcanized) or all-polymeric (i.e. entirely moulded) footwear Classe II Meaning for hybrid footwear For some applications, additional requirements may be provided (See footwear marking) Additional requirements for special applications Class I Penetration resistance X Conductive footwear X Antistatic footwear X Electrically insulating footwear heat insulation of sole complex X Whole cold insulation of sole complex X footwear Energy absorption of seat region X Water resistance X Metatarsal protection X Ankle protection X Cut resistance X Upper Water penetration and absorption X Resistance to hot contact X Outsole Resistance to fuel oil X The applicability of a requirement to a particular classification is indicated in this table by an X. Slip resistance (See footwear marking) Requirements Slip resistance on ceramic tile floor with lauryl sulphate (SLS) Slip resistance on steel floor with glycerine Floor types Hard industrial floors, for indoor uses (floor tiles in the food industry) Hard industrial floors, for indoor & outdoor uses (coating paint or resin floor in industry) All types of hard floors for multiple uses indoors or outdoors Slip resistance on ceramic tile floor with SLS and on steel floor with glycerine Coefficient of friction Heel slip ≥ 0,28 Flat slip ≥ 0,32 Heel slip ≥ 0,13 Flat slip ≥ 0,18 SRA + SRB Markings printed or embossed on the footwear Manufacturer’s brand Model Reference Size Year & month manufacture Standard Category & Symbols CLEMENT DESIGN Brand SUMMIT SUMMNOIR 42 18/10 EN ISO 20345:2011 S3 SRC Example for model SUMMIT Example for reference SUMMNOIR (SUMMIT black color) Example size 42 (available from size 35 to 48) Example for production date : 2018 october (Also batch number of the shoe) Example for safety shoes standard Example for S3 & SRC marking Guarantees the free trade of products and goods within the European Economic Community. The CE marking on the product means that the product meets the essential requirements of EU Regulation 2016/425 EU Declaration of conformity available on

Instruction for use These footwear are designed for general use, protecting against the risk of falls by slipping on floors of industrial type smooth, greasy or soft ground. For additional performance, refer to the marking on the shoes and the enclosed tables. Adjustment Once the shoes are attached, the foot must be perfectly maintained, no discomfort should be felt when walking. Otherwise choose a lower or upper size. Only the risks for which the corresponding symbol appears on the shoe are covered. Don’t use outside of its field of use defined in the instructions above. The tests were...