Alere™ Connectivity Pack I and II
24Pages

Alere™ Connectivity Pack I and II Annex to Alere™ q User Guide UG-Alere q-01 Englis

Alere Connectivity Pack I and II Alere™ Connectivity Pack I and II are recommended for use with the Alere™ q providing a wireless connectivity solution. Alere™ Connectivity Packs are distributed by: Alere Technologies GmbH Loebstedter Str. 103–105 D-07749 Jena, Germany www.alerehiv.com Alere™ Connectivity Pack I (Samba3G-E) Falcom Wireless Communications GmbH Gewerbering 6 D-98704 Langewiesen, Germany For more information, original User Manual and technical description of Samba3G-E please visit www.falcom.de/support/documentation Alere™ Connectivity Pack II (CT63) CEP AG Raiffeisenallee 12b...

CE Mark Manufacturer Attention symbol. Indicates special problems or important information. Read the accompanying text carefully. This product must be recycled or discarded according to applicable local and national regulations. Serial number Catalogue number To keep dry LOT number IMEI number Serial number Lead free device Alere Connectivity PackI and II

8 Prerequisites for the use of Alere™ Connectivity Packs 9 Alere™ Connectivity Pack I and II Specifications 2 Getting Started 11 Setting up the Mobile Network Connection 11 Inserting a SIM card into Alere™ Connectivity Pack I 12 Inserting a SIM card into Alere™ Connectivity Pack II 15 Connectivity Check Parameters 16 3 Sending Results from Archive

3 Sending Results from Archive 5 Technical Support & Error Messages Alere Connectivity Pack I and II

Alere™ Connectivity Pack I and II enable sending of result data from the archive of the Alere™ q to a defined remote server using a mobile network modem connected to an Alere™ q via USB port. Scope of Delivery Alere™ Connectivity Pack I (catalogue no. 260400015) includes 1x Alere™ Samba3G-E 1x USB extension cord

Alere™ Connectivity Pack II (catalogue no. 260400016) includes 1x CT63 Terminal 1x mini USB connection cord 1x xternal FME antenna (connect to the CT63 Terminal when e unpacking the Connectivity Pack) Acess to SIM card holder Alere Connectivity Pack I and II

Status LED The Status LED indicate various operating states of the mobile modems. For the Connectivity Pack I the LED is blue, for the Connectivity Pack II the LED is green. The different operating states are described in the table below. LED mode off fast blinking slow blinking permanently on Operating State modem is off net search/not registered registered full service transmission is active Prerequisites for the Use of Alere™ Connectivity Packs Connectivity requires a SIM card with an active account from a local network provider. To use Alere™ Connectivity Pack I an Alere™ q operating...

Alere Connectivity Pack I and II Specifications Data are reproduced from the original User Manual from the respective legal manufacturer. For more information please refer to page 2 of this document. Power Supply 5 V USB host powered 5 V USB host powered Antenna internal external FME (male) Note: Alere™ Connectivity Pack I and II are powered by the Alere™ q and might therefore impact on the charging state of the analyzer when running on battery. Alere Connectivity Pack I and II

Safety Warnings Alere™ Connectivity Packs utilize the GSM standard for cellular technology. GSM is an internationally established standard for radio communication. The modems are actually low power radio transmitters and receivers, similar to GSM cellular phones. Most electronic equipment, for example in hospitals and motor vehicles is shielded from radio frequency energy. However, radio waves may affect some malfunctioning or improperly shielded electronic equipment. Please consider special local or country specific safety standards, and where applicable, the relevant wiring rules....

2  Getting Started Setting up the Mobile Network Connection Note: n order to set up a network connection between the Alere™ q and a I remote server the analyzer needs to be configured. Please see section 4 for further details. Two simple steps are required to establish network connection: 1) nserting a SIM card with an active account from a mobile network i provider into the modem and 2) connect the modem to the configured Alere™ q. Inserting a SIM card into Alere™ Connectivity Pack I Insert the SIM card into the corresponding SIM card reader of the modem and slide it forward until it...

Inserting a SIM card into Alere™ Connectivity Pack II To insert the SIM card remove the SIM card reader cover panel by pushing it in the direction of the arrow embossed on the panel (1). The SIM card holder is now visible and the connectors lie exposed under the SIM card holder. Flip open the card holder (if the holder is locked, push it horizontally in the direction of the engraved arrow) (2). Completely insert the SIM card into the card holder so that the bevelled corner of the SIM card is on the top right, with the golden contact area facing you (3). Flip close the card holder and lock...

The proper function of the mobile network connection through the Alere™ Connectivity Packs can be tested as follows: • Connect the modem to one of the USB ports at the back of the Alere™ q. • Select «Settings» from the «Home» screen. • A list of options will open. Continue with «Advanced Settings». Settings Operator List ► Date and Time ^ Language ^ Advanced Settings ^ Alere Connectivity Pack I and II

• Then select «Connectivity». Advanced Settings Connectivity Calibrate Screen Test Mode • Finally initiate «Connectivity Check» . Connectivity Connectivity Check Note: he «Connectivity Check» option will T remain inactive until you connect the modem to the Alere™ q. Depending on the initialization status of the process a connectivity check may take up to 2 minutes. Manual Settings Import Settings