Screeni - IFU
24Pages

User manual

1. IMPORTANT INFORMATION – READ BEFORE USE “WARNING” indicates a particularly hazardous situation. Failure to observe the instruction may damage the instrument, cause injury, or even death. “CAUTION” indicates that use or improper use of the instrument may cause a problem, such as product malfunction, failure or damage. 1.1. Foreword This user manual contains essential information for the safe and optimal use of the Screeni. The information in this user manual is subject to change at any time, without notice. Make sure that you are using the latest version by logging onto the Axess Vision...

Observe all the warnings and precautions described in this manual. Otherwise, Axess Vision cannot be held liable in case of injury to the patient or user or damage to the device. The Screeni should only be used with endoscopes marketed by Axess Vision (see § 1.7 "Instrument compatibility"). The use of incompatible instruments may result in injury to the patient and impede the correct operation of the video-endoscopic system. Any modification of the Screeni by the user is strictly forbidden. Failure to comply with this instruction may result in injury to the patient or the user and/or impede...

Broncoflex® Agile Reference: 20030001 Applied part 2. DESCRIPTION OF THE SCREENI AND ACCESSORIES 2.1. Product description The Screeni is a non-sterile reusable medical device. It is a video processor with integrated touch interface designed to display live imaging data captured by sterile disposable endoscopes marketed by Axess Vision. For more information on the endoscope used, see the user manual of the endoscope (found in its transport box and available on the Axess Vision website https://endovision.tsc-group.com/). 2.2. Inspecting package contents When unpacking, any defective...

Touch screen display. Bumper for handling the Screeni. Screeni On/Off button. 3 The button lights up to indicate that the Screeni is switched on. Port for connecting the Axess Vision endoscope to the Screeni.

Flexible connector protection tab: USB port for USB key connection only (selfpowered hard discs must not be connected). Ethernet port. For use by qualified personnel for maintenance purposes only. Power connector 15V DC - 2A. Under this connector an LED indicates the charge status of the Screeni:  Orange: charging White: switched on, not charging Flashing orange: charging error (see § 7 “Troubleshooting”). Support feet / packaged endoscope support system when the system is attached to an IV pole (maximum load: 4 endoscopes). Stainless steel VESA 75 compatible mounting bracket. Stainless...

3.2. Installation The Screeni offers two installation possibilities: on feet, in which case it must be placed on a flat and stable horizontal surface, or fixed to a stable vertical tubular support *. 3.2.1. Assembly and disassembly on vertical tubular support a) Mounting 1) Unfold the quick-connect bracket. 2) Position the bracket on the vertical tube and tighten the knob until the assembly is immobilised. Make sure the Screeni is secure, without risk of falling or tipping. b) Removal Unscrew the knob while holding the Screeni and place it on a stable horizontal surface.

3.2.2. Quick removal and mounting of the Screeni leaving the fixing system on the vertical support a) Mounting 1) Ensure that the quick-connect bracket is properly installed ("Top" arrow on the side of the bracket facing upwards) and correctly tightened on the IV pole. 2) Present the Screeni at a 45° angle and slot it into the quickconnect bracket, then rotate it to the right or left until it locks. Check the stability of the assembly and that the lever is locked.

1) Raise the lever located on the back of the Screeni. 2) Holding the lever in the up position, rotate the Screeni to the right or left and remove it from its quick-connect bracket. 3.2.3. Tilting the Screeni When the Screeni is in position on its quick-connect bracket, it is possible to adjust its vertical tilt, holding the bumpers:

3.2.4. VESA mounting The Screeni can be mounted on a VESA 75x75 mount. To do this, remove the quick-connect bracket as described in § 3.2.2 "Quick removal and mounting of the Screeni leaving the fixing system on the vertical support". VESA mounting brackets (75x75) Next, attach the Screeni to the VESA mounting bracket (not supplied) using four M4 x 10 mm screws (not supplied). Comply with the size of the screws for VESA mounting to avoid any system damage. 3.3. Power connection See the list of connectors contained in the package, connect the appropriate power adaptor to the power supply...

1) Switch on the Screeni by pressing the "On/Off" button. When the home interface below is displayed, the system is operational: Battery charge level. Indication of software version. Access the examination manager. Access Screeni settings. Indication of the location of endoscope connection. 2) Check the battery charge level indicator (11) Logo displayed Battery power indicator Battery charging 100% - 80% 70% - 50% 40% - 20% 15% - 5% Battery fault (See § 7 “Troubleshooting”) 3) Connect the endoscope to the Screeni Connect the endoscope to the Screeni before using it on the patient. Before...

The system automatically switches to "live": Start/Stop a video recording of the current examination. Take a photo of the current examination. Examination name. Batch number of the endoscope in use. Symbol indicating whether the endoscope has already been used (absent by default). Last photo taken (pressing the last photo taken provides access to current examination management: see § 4.3 “Examination management”). Adjust "live" image brightness. Edit the examination name. “Live” indicator. 4) Check that a live video image appears on the screen. Point the distal tip of the Broncoflex display...

5) To finish the examination, disconnect the endoscope from the Screeni after removing it and moving it away from the patient. The home screen is displayed once more. See the instructions for use of the endoscope used for details concerning its disposal. Should the endoscope become disconnected during an examination, reconnect it, making sure to hold the connector by its plastic part. 4.2. System shutdown Disconnect the Broncoflex display device from the Screeni if you have not already done so. If the charge level of the Screeni battery is low, charge it (see § 3.3 "Power connection ")....