OPERATIONS GUIDE ATTENTION! Before installation and starting work with the unit, carefully read these guide! OPERATIONS GUIDE BLUEDENT SMART XPRESS cordless LED curing light CONTENTS: I. UNIT DESCRIPTION AND FUNCTION II. TECHNICAL DATA III. ACCESSORIES AND SPARES IV. SAFETY PRECAUTIONS V. PREPARATION AND SEQUENCE OF OPERATION VI. ROUTINE CARE AND MAINTENANCE VII. WARRANTY CONDITIONS VIII. BLUEDENT SMART DATA IX. SYMBOLS X. SERVICE DATA I. UNIT DESCRIPTION AND FUNCTION LED curing light BLUEDENT SMART XPRESS is a light source for intraoral polymerization of dental materials. The unit uses broadband LED (Light Emitting Diode) module as the light source. The emitted light is in the wavelength range 390-510 nm (the relevant range for camphor quinone containing products). BLUEDENT SMART XPRESS consists of Cordless handpiece and Charging station. BLUEDENT SMART XPRESS is produced in conformity with MDD 93/42/EEC and 2007/47/EC. II. TECHNICAL DATA 1. Operating voltage - 110-240V (±10%)/ 50-60Hz (see unit label) 2. Power consumption - 0,115-0,055 A 3. Dimensions: - Charging station length - 180 mm width - 130 mm height - 66 mm - Cordless handpiece diameter - 32 mm length - 196 mm 4. Weight: - Charging station - 560 g - Cordless handpiece (with battery) - 245 g 5. Light intensity - (S, P, L) 1500 / (H) 3500 mW/sq.cm. 6. Emitting time - (H) 3 - 3+3 - 3+3+3 sec. / (S),(P) 10 - 20 - 30 sec. /( L) 9 min./ ±5%/; 7. Emitted light - blue, 390 - 510 nm 8. Light source - broadband LED module 9. Curing modes - HYPER (H), STANDARD (S), PULSE (P), LONG (L) 10. Audible signal - every (H) 3 sec./ (S),(P) 10 sec. / ( L) 1 min. 11. Possibility for start and stop of Emitting handpiece at any moment. 2

IV. SAFETY PRECAUTIONS 12. Digital display of curing mode and countdown timer. 13. Battery - Li-Ion 2400 mAh, 3,7 V 14. Low battery indication. 15. Working mode (1 min. / 10 min.) As with all technical devices, the proper function and safe operation of this unit depend on the user's compliance with the standard safety procedures as well as the specific safety recommendations described in this Operations guide. The manufacturer of this unit declares to provide on request all additional necessary technical documentation / information which will help the user's technical staff to service the parts...

11. Pursuant to Directive 2002/96/EC, this symbol shows that the product must not be disposed of as urban waste at the end of its operating life. The product must be taken to centers specialized in separate collection of electric and electronic equipment. Correct disposal of the equipment, which is no longer used, prevents negative consequences for the environment and human health! V. PREPARATION AND SEQUENCE OF OPERATION S: Standard Light intensity (%) 100 STANDARD mode (10 - 20 - 30 sec.) - During the first 3 sec. llight intensity slowly increases from 0% to 100% of the light intensity (soft...

BATTERY MAINTENANCE, CHARGING AND REPLACEMENT The cordless handpiece is equipped with electronic charging control that ensures optimal battery charge and helps avoid overcharging. Select exposure time by pressing “TIMER” button repeatedly. The horizontal line shows selected time - 10, 20 or 30 sec. xpress HYPER 1. Curing mode display 2. Timer display 3. Curing mode selection 4. Timer selection 2 BLUEDENT 1 3s 6s 9s P_ 30s 20s 10s PULSE STANDARD H3 - HYPER mode with timer 3 sec. - Never place the handpiece in the charging station without the battery inserted in the handpiece! - When working with...

- The battery musi not be immersed in water or thrown in fire. - When discarding old battery, observe environment protection rules! OVERHEATING PROTECTION BLUEDENT LED SMART is equipped with system for overheating control. If the temperature of the LED source reaches 50 degrees C (122 degrees F), the countdown timer blinks and after that the display shows "Oh" (Overheating). After the exposure cycle Is completed, the curing light goes off. In this case place the handpiece in the charging station and as soon as it cools down to 40 degrees C (104 degrees F), Ihework can be continued. Vt. ROUTINE...

X. SERVICE DATA IX. SYMBOLS Manufacturer BG LIGHT LTD, 9-B, Luben Karavelov Str., 4002 Plovdiv, Bulgaria Pursuant to Directive 2002/96/EC, this symbol shows that the product must not bedisposed of as urban waste at the end of its operating life. Pay attention to the instructions accompanied by this symbol. Fragile! Product with CE mark. Applied part type B. The device is equipped with double electric insulation (Class II) W s W Hz mm A V Pa °C g Ohm (electric resistance unit) Second (time unit) Watt (power unit) Hertz (frequency unit) Milimeter (length unit) Amper (electric current unit) Volt...