BT104
1 / 16Pages

START STOP BLOOD PRESSURE MONITOR

Components of the Device CUFF CUFF TUBE CUFF TUBE CONNECTOR START STOP START/STOP BUTTON IRREGULAR HEARTBEAT INDICATOR BATTERY DOOR SYSTOLIC MEASUREMENT DIASTOLIC MEASUREMENT PULSE MEASUREMENT BATTERY COMPARTMENT

If this is your first time using the device: 1. Slide open the battery door on the back of the device. 2. Install the batteries provided with the device. Follow the diagram inside the battery compartment for correct polarity — the springs should align with the negative sign on the batteries. 3. Slide the battery door closed.

Securing the Cuff 1. Plug the connector on cuff tube into the device. START STOP 2. Expose your left upper arm by removing or adjusting clothing and jewelry. Make sure blood flow is not constricted by a rolled up sleeve. 3. Open the cuff and loosen fully. 4. Orient the cuff so that the tube exits towards the hand. 5. Place your arm through the cuff loop, with your palm facing up. 6. Position the cuff’s edge about an inch (2-3 cm) above the elbow.

7. Align the Ф marker (located to the right of tube exit) with the center of your arm. 8. Tighten the cuff evenly around your arm by pulling on the end — make sure the Ф marker stays aligned with the center of your arm. 9. Wrap the end of the cuff over your arm to secure it in place. Don’t make it too tight — allow a finger to fit between the cuff and your arm.

Taking a Measurement 10. Lay your arm on a table with your palm facing up. The cuff should be at the same height as your heart. Sit up straight and rest your feet flat on the ground. Make sure the tube is not kinked or pinched. 11. Press the START/STOP button on the device to turn it on. 12. Wait for the device to power on, and perform the measurement while inflating the cuff. 13. When the measurement concludes, results are shown on the display and the cuff automatically deflates. 14. Remove the cuff after it deflates.

15. The device automatically transmits measurement results. During this process an indicator is shown in the middle of the display. Transmission successful 16. When the measurement is successfully transmitted, the device shows the following indication before powering off Notes: • If you wish to abort the measurement while the cuff is inflating, press and hold the START / STOP button for 5 seconds. • If the device detects an irregular heartbeat, the display will show this indicator along with the measurement results. While this may not be a reason for immediate concern, contact your primary...

Precautions • Only use Duracell alkaline AA batteries with this device as these offer the longest battery life. Other brands may not be able provide sufficient power for cellular data transmission. • This device is for adults. Do not use it on children unless otherwise instructed by a medical professional. • Do not use or store the device near infants or in an area they can reach. • Do not apply the cuff on an arm that has: • an unhealed wound, • another medical device attached, or • an intravenous drip or blood transfusion attached. • Do not use this device if you have an implanted cardiac...

Troubleshooting Problem Possible Reason Device doesn’t power on when START/STOP button is pressed. Batteries completely drained. Replace batteries with new Duracell AA. Batteries inserted with incorrect polarity. Remove batteries and reinstall them making sure the + and - polarity symbols on the batteries match those inside the battery compartment. Cuff does not inflate. (display turns on) Cuff not plugged in correctly. Make sure the connector on cuff tube is plugged all the way into the device. Cuff doesn’t form a loop around arm. To form a loop: pass the end of the cuff furthest away from...

Problem Readings too high or low. Possible Reason Cuff not positioned correctly. Review instructions on Securing the Cuff, and retry measurement. Movement during measurement. Place your arm on a table with your palm facing up. The cuff should be at the same level as your heart. Make sure you stay still and don’t talk during measurement. Measurement results differ from those measured at doctor’s office. Measurements taken in a medical / professional environment (white coat effect) may affect your blood pressure. Measurements taken in a more relaxed, home environment may avoid effects...

Error Codes Code Replace batteries with four Duracell AAs. Movement detected Avoid moving or talking while taking a measurement. After securing the cuff and assuming the correct posture, consider waiting for five minutes to settle down before starting a measurement. Confirm that the cuff is secured correctly on your exposed arm. Remove all clothing and jewelry from your arm. If you feel unwell, contact a medical professional. Cellular connection error Data transmission error Move to another area, closer to a window. Use the device at a location where you get trong cellular signal with your...

Subscription suspended Contact customer support. Subscription terminated Contact customer support.

Storage and Maintenance • Only use Duracell AA batteries with the device. • Store your device and cuff in a clean and dry place. • Avoid exposure to direct sunlight, moisture, extreme heat, cold or humidity. • Avoid exposure to vibration, shaking or other mechanical stresses. • Make sure the rubber tube of the cuff is not squeezed, stretched or kinked during use and storage. • Avoid twisting or folding the cuff and tube too tightly as this may cause damage over time. • Clean both device and cuff with a soft, dry cloth. If necessary use a dampened cloth and natural detergent. Do not use...

Symbols Symbol Description Type BF applied part Cuff circumference Date of manufacture Complies with FCC regulations Relative humidity range Caution: consult instructions for use Temperature range Do not dispose of this product as unsorted municipal waste, take it for recycling. REF Model number Serial number / IMEI Ingress Protection Effective against fingers or small objects; dripping water