BOXER Boxer Pumps > Products > Peristaltic Pump 15KS peristaltic pump with DC / Gear Motor. Technical Data Flow per Revolution ID 0 1.6 mm tube ID 0 2.4 mm tube ID 0 3.2 mm tube ID 0 4.8 mm tube Power Consumption Terminal Resistance Motor Termination Motor Insulation Class Tube Materials Pharm-a-line / Silicone / Norprene G / ED-Plex General Data Max pressure Max suction height (dry) DC motor life 405 g All data measured with 'run-in' Pharm-a-line tubing and H2O.

BOXER Boxer Pumps > Products > Peristaltic Pump Flow Data Flow Range (ml/min) with 12 V / 40 rpm Motor:

BOXER Boxer Pumps > Products > Peristaltic Pump Flow Range (ml/min) with 24 V / 298 rpm Motor: Min at approx. 50% nominal motor volatge, Max at nominal voltage The 15KS peristaltic pump is a flip-top design. The loading and unloading of the tube is through operation of the lever: The tube grips are sprung loaded and adjust automatically to the OD of the tube. The 15KS is designed for 1.6 mm wall tubing from ID of 1.6 to 4.8 mm. Only tubing suitable for peristaltic pumps should be used.

15KS Series - DC / Gear Motor Boxer Pumps > Products > Peristaltic Pump Links to Drawing and STEP file: → Drawing (.png) → STEP (.zip)

15KS Series - DC / Gear Motor Boxer Pumps > Products > Peristaltic Pump Removal / Assembly of Pump Head The 15KS peristaltic pump is designed with a bayonet style head assembly onto the motor plate. ❶ Open the tube clamp lever completely. ❷ Remove the M3x12mm screw. Close clamp lever. ❸ Push head lock lever in direction on the motor. Rotate the head anti clockwise. ❹ Pull the head assembly away from the motor plate. Head lock lever ❺ To re-assemble: open tube clamp lever. Align head with motor plate at the angle shown below. Rotate pump rotor until the rotor is aligned with drive pin. Push head...

15KS Series - DC / Gear Motor Boxer Pumps > Products > Peristaltic Pump Assembly Information The 15KS peristaltic pump with DC / Gear is assembled to a panel cut-out using 4 x M3 bolts. To access the mounting holes the head assembly should be removed following the instructions on the previous page. The mounting plate is designed for several different motors. The 4 x 3.2 mm mounting holes are recommended for the DC / Gear version. The mounting gasket should be placed between the motor plate and panel. Recommended panel cut-out:

BOXER Boxer Pumps > Products > Peristaltic Pump Encoder The 15KS peristaltic pump with DC / Gear is available with a dual channel encoder mounted on the rear of the motor. Each channel is switched by a hall effect sensor triggered by a 5 pole rotating magnet. The output is 5 pulses per motor revolution. Since the encoder is placed on the motor shaft, the number of pulses per pump revolution depends on the gear ratio and nominal speed of the motor and so varies according to each motor version: 500 pulses per revolution 95 pulses per revolution 70 pulses per revolution 500 pulses per revolution...

BOXER Boxer Pumps > Products > Peristaltic Pump Part Number Description Please enquire for part numbers of other configurations. Sample quantities are available for direct online purchase: ^ BOX-it Tubing should always be ordered separately. Listed here is Pharm-a-line (PHI) tubing in 150 mm single lengths, 1m (or multiples of) lengths or 15 m coils: Description Tube length Tube length Tube length Tube length Tube length Tube length Tube length Tube length Tube length Tube length Tube length Tube length Technical information including chemical compatibility: Part Number mm x 150 mm mm x 150 mm mm...