Diode Laser+ Pico Laser Diode Laser+Pico Laser System

Diode Laser+ Pico Laser User Manual Model: KH-6 Welcome to use KH-6 diode laser + pico laser system. The system uses 808nm or 755/808/1064nm diode laser and offers painless permanent hair reduction. And pico laser system.

Diode Laser+ Pico Laser 1. KH-6 diode laser + pico laser machine could emit the high-intensity infrared laser beam. Please follow some operation regulations: • According to the standard of NOHD, please wear the suitable protection glasses for operator and patient in order to protect the eyes, • Please do not point the laser at the eyes directly. 2. Please make sure to be familiar with the structure and manual before operation. 3. Diode Laser Hair Removal Machine is only allowed to be used by people who had enough safety and operation training. Please turn off the cooling function, when the machine...

Diode Laser+ Pico Laser

Diode Laser+ Pico Laser 4.Basic machine structure Pico Laser Handle Diode laser Light Indicator Emergency Switch

Diode Laser+ Pico Laser 5. Machine Installation Do not power up the system before you read this manual! 1. Please check all the parts in package list to confirm all are received. 2. Add water to water tank. Please confirm your machine model. KH-6 has micro-channel laser stack in the handle piece. It needs DI-water,otherwise laser handle piece is easily broken. Operation way is as follows. A. Connect water valves to water inlet and Unscrew the drain screw at the same time. B. Connect the funnel to the water valve of water inlet, then add water. When water overflows from the water drain, it means...

Diode Laser+ Pico Laser you are successfully enter the hair removal system. Please follow the “6. OPERATION” chapter to start the treatment. 6) For any emergency situation, please press the emergency button (Red Mushroom) to shut down the laser immediately. 7) After treatment, if you want to turn off the system, you can use the key to shut it down directly. And turn off the air switch at the back panel. You can remove the VAC plug if necessary. Here is a welcome page. Just press “Start” Bottom , you will enter the second page. In this page, you can choose the working mode, the size of the treatment...

100 : : 14.0SHR When you enter into SHR Page,you can adjust fluence and energy by “A” and “V”. In addition, you can press”Save” to keep your preferred parameter in record,then you can use the new parameter in next treatment. There are totally 3 parameters to be set, including: Fluence, PULSEWIDTH and FREQUENCY. 1) FLUENCE shows energy value of a single pulse laser per unit area. The step width is 1J/cm2. You can adjust it by pressing “A” and “V”. 2) ENERGY shows energy value of a single pulse laser. The step width is 1 KJ. You can adjust it by pressing “A” and “V 3) GRIDSIZE is the number of...

Diode Laser+ Pico Laser 5) Sec shows treatment time. It is set by Number of Grids and countdown, when it becomes “0”, treatment is finished. 6) Home means back. 7) Save is to keep your preferred parameter. 8) Reset is to back to recommended parameter quickly. 9) Setting is used to set the system parameters. The appearance has been set without the need for user Setting. 10) Language is used to set the Language. 11) INFO is used to display system information. In this condition, you can set the parameter. Working It means that the machine is working, you can’t set the parameter. It shows the system...

Diode Laser+ Pico Laser 1) Fluence shows energy value of a single pulse laser per unit area. The step width is 1J/cm2. You can adjust it by press “A” and “V”. 2) Frequency shows the pulses per second of the laser. A higher repetition rate leads to higher pulse energy fluence. The frequency can be variable from 1 Hz~10Hz with a step width of 1 Hz. 3) Please refer to explanation of “SHR Mode” for other buttons.

Diode Laser+ Pico Laser 1) FLUENCE shows energy value of a single pulse laser per unit area. The step width is 5J/cm2. You can adjust it by press “A” and “V”. 2) ENERGY Fixed frequency is 1 HZ, accumulated light energy. 3) Please refer to explanation of “SHR Mode” for other buttons.

Diode Laser+ Pico Laser PicoLaser Interface 1)Different wavelengths can be selected for treatment. 2)Fluence shows energy value of a single pulse laser per unit area. The step width is 1mj. You can adjust it by press “△” and “▽”. 3) Frequency shows the pulses per second of the laser. A higher repetition rate leads to higher

Diode Laser+ Pico Laser energy fluence. The frequency can be variable from 1 Hz~10Hz with a step width of 1 Hz. 1. The treatment of the hair removal needs experienced professionals. Do not use it if you have no experience for such kind of laser device. 2. Operators and patients must wear laser goggles to protect eyes from any laser damage threat. 3. Please notice that this is a high power laser device and if the patients feel very painful, please stop the laser and check if there is anything happening to the patients’ skin. Adjust it as a proper power that the patients can stand to do the tr...

Diode Laser+ Pico Laser 7. Do not shot the laser at random targets, or it may cause burning or fire. 8. Always keep the handle piece with the holder on the main machine when you don’t use it. Otherwise, the condensing water may flow back to the laser stack in handle piece, so that cause laser failed. 9. If you won’t use the machine over 2 weeks, please draw off the water from the machine. A. Connect water valves to water drain and water outlet at the same time. B. Connect the funnel to the water valve of water outlet, then water flows out. Be sure to use a basin to catch the water. C. After operation,...

Diode Laser+ Pico Laser the water circle system, then let the water pump working for a while, the water flow rate should rise up.