SLIMIMPLANT LINE PRODUCT CATALOGUE www.dentaltechworldwide.com

BWS® Implant Surface 4 Implant Line ImpLogic® AT 3.25 5 Implant Line ImpLassic FT3 3.25 6 ImpLogic® AT - Recommended surgical sequence and drill speed 8 ImpLassic FT3 - Recommended surgical sequence and drill speed 8 Drills - Reading depth notches and sharp drills 9 Drill Stop - Stop insertion and removal procedure 10 Implant Drivers - Implants insertion procedure 11 Components for cemented/screwed prosthesis 12 Components for MUA screwed prosthesis 13 Prosthetic components for digital flow 14 Prosthetic components for digital flow - Connection on MUA 17 Overdenture prosthetic components 18 Dynamometric...

SANDBLASTING AND ACID ETCHING Sandblasting and etching processes of the implant surface allow to obtain optimal roughness values that make the adhesion of fibrin to the surface more tenacious and facilitate the bone healing process, significantly reducing the time. FIBRIN ADHERENCE The capacity of BWS® to retain fibrin, lets osteoblasts migrate from the bone to the implant surface and reproduce there, generating new bone in direct contact with the titanium (contact Osseointegration). THE IMPLEMENTED PROTOCOL PROVIDES VERIFICATION OF EACH BATCH OF PRODUCTION After the surface treatment and the...

Implant Line ImpLogic® AT 3.25 (Active Thread) Tapered implant that, thanks to its special spiral design, facilitates the users in the realization of Ridge Expansion procedures. The exceptional self tapping power of the thread, provides an excellent bone condensing and a high primary stability even in very complex clinical cases. ImpLogic® AT is recommended in cases of post extraction implants and in case of poor quality bone. SPIRAL DESIGN The unusual spiral design simplifies the procedures of Ridge Expansion. RISK REDUCTION Less risk of damaging adjacent teeth and perforation of the lingual...

Implant Line ImpLassic FT3 3.25 Fixture with cylindrical body and a conical apex Modulating the surgical procedure it is indicated in all bone types; even in the case of non-compact bone it is able to achieve a good primary stability. You can use it for any type of prosthetic restoration, screwed and cemented. Using the concept of platform switching allows you to better manage the soft tissue in the area of the implant – abutment interface, and reduce peri-implant bone resorption over time. BETTER PENETRATION Spiral profile with hybrid progress: flat and radiating towards the root, triangular-shaped...

ImpLogic® AT DIAMETER - Ø 3.25 mm Cover screw included Color Code Warning! All DRP drills are 0.8 mm longer than the implant. In the planning stage and while drilling in proximity to vital anatomical structures, this added length must be considered. Indication of surgical position Recommended surgical sequence Bone D4/3 Color Code Cover screw included Warning! All DRP drills are 0.8 mm longer than the implant. In the planning stage and while drilling in proximity to vital anatomical structures, this added length must be considered. radio-checked Optional radio-checked Indication of surgical position...

LEGENDREQUIRED checkmarkOPTIONAL © Warning ! In the table “Recommended surgical sequence and drill speed” parameters should be considered as general indications; the clinical evaluation should always be subjected to careful analysis by the practitioner in each specific case. Based on the clinical features and bone consistency detected at the time of implant surgery, the choice of the available instrumentation will be made by the practitioner. LEGEND REQUIRED checkmark Warning ! In the table “Recommended surgical sequence and drill speed” parameters should be considered as general indications;...

Lance drill - Parallel drills - Countersink - Tappers Lance drill Parallel drills Drill stop STOP 0 4-5 mm Material: Ti5 Parallel drill L 23 mm Material: Inox Implant lenght (L) mm Countersink Material: Inox The Tappers can be used, at the operator's discretion, based on the bone consistency found at the surgical site and to reduce the implant insertion tension.

Drill Stop - Stop insertion and removal procedure STOP insertion Hold the drill on the stalk side and insert the stop, with the retentions facing the drill, until the point of contact with the metallic stop located on the drill itself. (Fig. 1 - 2- 3). Warning WRONG insertion STOP Stop insertion with the retentions facing the tip of the drill is incorrect. (fig. 4 - 5). STOP removal Hold the stop and remove the drill by pulling on the stalk side. Depth STOP for different lengths. The advantages: » Optimal check-depth during preparation of the surgical site, even in conditions of poor visibility...

With manual implant driver Insert the implant driver connected to the handwheel into the implant making a slight rotation to allow good matching of the two geometric figures (implant - driver) and remove the implant (Fig. 6). Begin insertion of the implant in the alveolar surgical site using the manual implant driver. Where bone density permits, it is possible complete insertion of the implant using the manual wrenches (Fig. 7). To remove, exercise a slight lateral movement, right and left, in order to free the matching (Fig. 7). Insert the direct contra-angle implant driver into the implant...

Components for cemented/screwed prosthesis Taper healing abutment Material: Ti5 Closed tray impression coping Material: Ti5 Fastening screw included REF VTST32 Open tray impression coping Material: Ti5 Fastening screw included REF VTPR3200 Implant analog Material: Ti5 Fastening screw included REF VFD032 Straight abutment Material: Ti5 H Castable abutment Material: Pmma Straight abutment Package 10 pcs. Material: Ti5 Angled abutment Material: Ti5 Overcast abutment Material: CRCO REF 7,5mm 5,5mm 3,5mm Cutting line for use in digital environment Cylinder abutment Material: Ti5

MUA protection cap 03.25 Material: Ti5 Package 2 pcs. Fastening screw included REF VPCEM Supplied with transport and parallelization screw Fastening screw included REF VMF325 MUA CrCo 03.25 Material: CRCO Fastening screw included REF VPCEM MUA castable 03.25 Material: Pmma Fastening screw included REF VPCEM