New products 2015
12Pages

{{requestButtons}}

Catalog excerpts

New products 2015 - 1

Playsafe triple light

Open the catalog to page 1
New products 2015 - 2

    Erkoform-3d + thermoforming unit with reserve-vacuum and touchpanel Erkoform-3d +, technical data: height 31.5 • width 35 • depth 37 cm foil diameter 120 mm • foil thickness 0 - 5.5 mm weight 13.9 kg • ~230/240/110/115 volts • 360 watt max. vacuum 0.8 bar • noise level < 70 dB(A) 1 • The Erkoform-3d + is a noticeable further development of the well-proven Erkoform-3d. In principle it is an Erkoform-3dmotion without automated thermoforming process. • No compressed-air supply required - plug and play. • Touchless temperature sensor for accurate determination of the actual thermoforming...

Open the catalog to page 2
New products 2015 - 3

The program contains all Erkodent thermoforming materials, leads as short guide with animations through the sequence of work and indicates the required working steps. Select desired foil and thickness, start. The indicated thermoforming temperature and the cooling time can be changed for special applications without influencing the basic program. Often used foils can be saved as favorites. New foils can be saved as favorites. Also changed factory settings can be saved as favorites. The unit can be upgraded with the Occluform-3 which allows to imprint the opposing bite directly during the...

Open the catalog to page 3
New products 2015 - 4

   Erkoplast PLA thermoforming material on the base of natural lactid acids (polylactides) Erkoplast PLA replaces the previous Erkoplast and Erkorit types (petroleum-based polystyrenes). Base for the Erkoplast PLA types is the natural occuring polylactide. Mainly starches for ex. out of maize or other agricultural waste are used as raw materials. Erkoplast PLA is recommended for the fabrication of individual impression trays and base plates (bite plates). In regard to the physical and processing properties they exceed the previous types Erkoplast and Erkorit. (contents) Erkoplast PLA-T,...

Open the catalog to page 4
New products 2015 - 5

The new PLA-handles in flat and high version will be reliably fixed by heat to Erkoplast PLA. Best already during the thermoforming process. No primer is needed. (With LG-Primer and heat the PLA-handles can also be used for the previous types Erkoplast and Erkorit.) The base of the PLA-handle and the ridge should roughly fit together. If necessary, soften and adapt the handle base by heating in boiling water, with the hot-air burner (177 540) or a hot air gun. PLA-handles, 222 500, 50 pieces, high Thermoform and immediately place the PLA-handle onto the desired area and slightly press into...

Open the catalog to page 5
New products 2015 - 6

   Playsafe triple light a thinner version of the popular Playsafe triple for small mouths Playsafe triple light meets the demand to offer a comfortable sports mouthguard with highest protection effect also for small mouths. The Playsafe triple foils are three-layered, soft at the inside and outside and in between hard. The Playsafe triple foil has a thickness of 5.5 mm. The Playsafe triple light foil has a thickness of 4.1 mm. 5 The higher protective effect of laminated sports mouthguards in comparison to single-layered ones is well-known. The fabrication of a laminated sports mouthguard,...

Open the catalog to page 6
New products 2015 - 7

power distribution of a hitting impact of the different sports mouthguard types: Erkoflex Triple layer Erkoflex power distribution foil thicknesses: Playsafe triple light Playsafe triple soft, 1.5 mm 2.5 mm hard, 0.6 mm 1.0 mm soft, 2.0 mm 2.0 mm

Open the catalog to page 7
New products 2015 - 8

   Playsafe 4 u completely free indvidualisation of the Playsafe sports mouthguard types A high-quality UV printing technique allows Erkodent to print preferred designs in intense colours directly on Erkoflex (thickness 0.7 mm). Each design* is possible, but to be readable in the recommended size of about 12 mm height it should not be too detailed. The width respectively length is variable. Very long designs should be divided when applying to the Playsafe sports mouthguard. The print will be delivered on Erkoflex in the thickness of 0.7 mm and the size of 60 x 40 mm. Procedure: • Choose...

Open the catalog to page 8
New products 2015 - 9

The primary goal of this offer is to enable to the athlete each preferred design. Erkodent offers therefore a small selection of designs. As of April 2015 these will be published at www.erkodent.de. The selection will include for ex. flags, figures in different optics and several licence free designs.

Open the catalog to page 9
New products 2015 - 10

    Lisko-B prepolishing disc with a considerably higher service life The successful Lisko polishing disc family has now been extended by a version with a coarse graining to prepolish hard thermoforming materials. The graining is equal to Lisko brown. Because of the bound structure Lisko-B has a considerably higher life time and remains longer in its basic shape without spreading. With these discs even thick, hard splints (for ex. Erkodur and Erkoloc-pro 3.0 - 5.0 mm) can be ground to size, prepolished and finished without grinding marks at the edges or at the surface. Recommended number of...

Open the catalog to page 10
New products 2015 - 12

Erkodent Erich Kopp GmbH Siemensstraße 3 • 72285 Pfalzgrafenweiler • Germany Tel.: + 49 (0) 74 45/85 01-0 • Fax: + 49 (0) 74 45/20 92 info@erkodent.com • www.erkodent.com DIN EN ISO 13485 : 2012 /

Open the catalog to page 12

All ERKODENT Erich Kopp catalogs and technical brochures

  1. Thermoforming

    40 Pages

  2. Program

    28 Pages

  3. silensor-sl

    2 Pages

  4. Thermoforming

    40 Pages

  5. tztG_EN

    12 Pages

  6. Erkoform-3

    1 Pages

Archived catalogs

  1. Erkoform-3d

    2 Pages