Catalog excerpts
Dental laboratory Ceramic furnaces Ceramic furnaces designed and manufactured to ensure the best performance and reliability for each kind of ceramic. With electronic vacuum control. With large LCD display. With quartz chamber. Max temperature 1200 °C. Self-calibration program. Manual calibration. Vacuum 759,5 mm/Hg. Input voltage 230 V ac 50/60 Hz. Overall dimensions 40 W x 45 D x 53 H cm. Power (without pump) 1200 W. Weight 29 kg. EFP 100 - Traditional ceramic furnace. With 100 programs each of them composed by 15 parameters that can be EFP 100 P - Press-injection ceramic furnace. With 20 programs for press-injection each of them composed by 14 parameters that can be preset by the operator and 80 programs for traditional ceramic with 15 parameters that can be preset by the operator. Supplied with manual pressure regulator and manometer for the visualization. PVFC - Dry vacuum pump for ceramic furnaces. Input voltage 230 V ac 50/60 Hz. Load 50 lt/min. Power 200 W. Weight Kg 7,3. Device which allows photopolymerization of all active photo materials available on the market. It is equipped with 8 fluorescent lamps and one 150W halogen lamp, arranged around a rotating plate, which emits UVA rays and white light (photopolymerization range 320/550 nm). It also has a cooling fan so it is possible to work for long periods of time without overheating the materials. During photopolymerization, the inside temperature does not exceed 50°C. Through an electronic microprocessor control it is possible to set a cycle either with or without the halogen lamp, to set photopolymerization time, to run or not run the final cooling cycle. Standard equipment: four 4* 9 W PLS910 lamps - four 4* 9 W PLS952 lamps - one 150 W halogen lamp - five support pins - one perforated Plexiglas plate. Input voltage 230 V ac 50/60 Hz. Overall dimensions: 22x28x25 cm. Power 320 W. Weight 10 kg. EU ROC EM s.r.l. - Via Darwin, 20 - 20019 SETTIMO MILANESE (Ml) - Italy e-mail: info@eurocemitalia.com -www.eurocemitalia.com EUROCEM s.r.l. reserves itself the right to modify its equipment whenever necessary without notice.
Open the catalog to page 1Pre-heating oven ECF 3N series Pre heating oven ECF 3N series with a new simple and functional electronic card which controls a three-stage cycle with temperatures, rising speed and standby times that may be preset by the operator according to his needs. LCD display. Possibility to preset the cooling phase. Timer for deferred ignition which may be set up to 99 hours and 59 minutes. Final temperature which may be preset up to 1100 °C. Heating system by muffle with resistances on the four sides. Set for the connection to an extractor equipped with intake fan (AS) controlled by card with two...
Open the catalog to page 2Centrifugal machine for blowpipe casting For blowpipe casting. Digital motor rotation time adjustment (range set by the operator: 15/60 seconds). Digital initial force adjustment (range set by operator: 5 steps with sequential adjustment). Device to detect correct position of the arms. Handy systems to quickly balance arms and centre the cylinder. Mechanical door lock sets in when cycle starts. Switch to turn off motor when cycle is running Safety microswitch. Input voltage 230 V ac 50 hz. Power 1400 W. EC K 60 - Model without base Overall dimensions 60,5W x 55D x 32H cm. Weight 39 kg. ECK...
Open the catalog to page 3Steam generators EGV 28 PLUS - Steam generator directly connected to the water works or outside tank. Working pressure from 2 to 8 bar preset by the operator through an electronic card with visualization on the display of the pressure inside the boiler. Steam function through a fixed nozzle. Water, steam and water/steam function through gun with flow regulation. Low tension pedal control. Safety devices: manual reset pressure switch and safety valve. Control for minimum and maximum water level inside the boiler. Control for pump perfect running with heater deactivation and visualization on...
Open the catalog to page 4Mixers for plasters and investments ECM 500P - For plasters and investments. Possibility to run the whole mixing and pouring cycle in partial or total vacuum. Vacuum release adjustment. Supplied with internal vacuum pump (2 m3/h - vacuum greater than 70 cm/Hg). Digital adjustment of the mixing time (range which may be preset by the operator 5/120 seconds). Complete with vibrator at digital adjustable intensity. Complete with investment bowl with 500 g capacity (available on request 500 g plaster bowl). Speed 230 rpm. Input voltage 230 V ac 50 Hz. Power 400 W. Overall dimensions 31W x 35D x...
Open the catalog to page 5EMT 1400 - Water model trimmer. With solenoid valve for water. With bakelitic disc. Speed 2800 rpm. Overall dimensions 30W x 40D x 30H cm. Working table high 15 cm. Weight 17 kg. Input voltage 230 V ac 50 Hz. Power 600 W. Model trimmers EMT 2S00 - Dry model trimmer. Preset for connecting the outside aspirator. With diamond disc. Speed 2800 rpm. Overall dimensions 30W x 40D x 30H cm. Working table high 15 cm. Weight 17 kg. Input voltage 230 V ac 50 Hz. Power 600 W. Plaster drilling device EFC 130 Drilling device for plaster mouldings, Plexiglas or PVC bases to drive conical pins into the...
Open the catalog to page 6ESB 3 - Three sand version. Possibility of sanding with aluminium oxide and/or glass microspheres from 25 urn to 250 urn. When placing the order the operator can select the modules to be installed according to his needs among three different sizes (25/50 pm nozzle d. 0,5 - 50/100 pm nozzle d. 0,8 -110/250 pm nozzle d. 1,3). Preset for connecting the outside aspirator. Pedal control. Perfect visibility and excellent lighting. Single sand selector placed inside the sandblasting box. Pressure regulator and pressure gauge for each cylinder. Door with knob for a perfect closure of the...
Open the catalog to page 7prostheses. With fixed nozzle. Pedal control. Perfect lighting. Pressure gauge. Door with knob box. Air filter. With gloves. Input voltage 230 V ac 50/60 Hz. Power 9 W. Overall For sanders small dimensions for an easy positioning inside the dental laboratory. Special filtering system for extra fine sands. High power by-pass motor. For sanders for model trimmer. As ECS 1 with special filtering system for plaster For 4 muffles (tank dimensions 17W x 32D x 25H cm). With electronic card for programming 2 phases (1st phase: pre-heating - 2nd phase: boiling). Pre-heating and boiling times,...
Open the catalog to page 8