For the harshest environmental conditions

SPECIALIST FOR CIRCULAR CONNECTORS The HEC series is part of our extensive range of power connectors, making it suitable for virtually any low and high voltage application. This enables versatility, which is also reflected in the possible areas of application. These include agricultural and construction machinery, chemical plants/process engineering, mining and surface mining, mechanical engineering and non-contact areas in the food industry. Connectors for harsh environments of the HEC Series 696 are available as cable connectors and rectangular panel mount versions with or without integrated...

■ Diameter cable parts 36 mm, panel mount parts 40 mm

SECTORS AND FIELDS OF APPLICATION Mining and surface mining Chemical and process engineering Non-contact food industry Agricultural and construction machinery Mechanical engineering and materials handling

■ PowerBayonet HEC • 696 Series • Bayonet locking system • Crimp termination • Diameter cable connectors 36 mm, Panel mount connectors 40 x 40 mm • Protective hose fitting • Panel mount connectors with hinged cover • Designed for harsh environments

■ Compact design: Power supply for your system or drive unit even in confined spaces. ■ Hybrid design for simultaneous power supply and signal transmission with only one plug-in. ■ Good chemical and corrosion resistance for use in the non-contact food industry and process engineering.

Male cable connector Male cable connector, protective hose fitting Crimp and strip contacts see page 17/18 Crimp and strip contacts see page 17/18

Female cable connector Crimp and strip contacts see page 17/18 Crimp and strip contacts see page 17/18

Male panel mount connector Male panel mount connector, protective hose fitting Crimp and strip contacts see page 17/18 Crimp and strip contacts see page 17/18

Female panel mount connector Crimp and strip contacts see page 17/18

Bayonet HEC Assembly instruction Cable connectors 5 and 8 contacts 1. Strip to L = X mm length and take off cable jacket. 2. Bead pressing screw, pinch ring, seal and distance sleeve to cable. 3. Strip insulation of the single wires (length Y mm). 4. Crimp contacts to single wires.* 5. Press crimped contacts into contact carrier until they snap into place. Then push the carrier into the connector sleeve to block. 6. Put locking unit to the thread of the connector sleeve and screw it towards the direction marked with an arrow until it is tight. 7. Push sealing ring into the pinch ring to block...

Assembly instruction Cable connectors 12 contacts 1. Strip to L = 50 mm length and take off cable jacket. 2. Bead pressing screw, pinch ring, seal and distance sleeve to cable. 3. Strip insulation of the single wires to L = 3.5 mm. 4. Crimp contacts to single wires.* 5. Press crimped contacts into contact carrier until they snap into place. Then push the carrier into the connector sleeve to block. Attention! Bear in mind the positioning of the contacts in relation to the housing. The positioning of the contacts is stamped on the contact carrier. 6. Put locking unit to the thread of the connector...

Bayonet HEC Assembly instruction Panel mount connectors 5 and 8 contacts 1. Strip single wires to L = 7 mm. 2. Crimp contacts to wires.* 3. Press crimped contacts into contact carrier until they snap into place. 3.1. Alternatively when using the single wire seal: ** Pierce through the needed sections of the single wire sealings with a pointed device or tool and then raise them over the contacts. Then press contacts into the contact carrier, lay the single wire sealings flat onto the contact carrier, press pressure ring to stop and finally fix it with the pressing screw. 4. Push the pressing screw...

Component part drawing option with set of sealings Panel mount connectors male insert male housing flat seal female housing female insert Contact arrangements Male insert (mating side) Female insert (mating side) Alternative with flattening

Male contact, signal, PU 100 pieces, Female contact, power, PU 100 pieces, Female contact, signal, PU 100 pieces,

Crimp measures, hight dimension (standard value) Crimp measures, hight dimension (standard value) Strip contact (Male), Strip contact (Female),

Accessories Power Crimping tool for turned crimp contacts Crimping tool for stamped single contacts Crimping tool for strip contacts Extraction tool for turned contacts Signal contact Power contact Extraction tool for stamped crimp contacts Protective hose fitting for cable connectors securing clip seal hose seal 12 Pressing screw, securing clip and hose seal are enclosed loose in the bag Protective hose fitting, 50 m

Seal for single wires, thrust ring, pressing screw, securing clip and hose seal are enclosed loose in the bag Protection cap for male cable connector - 165 Protection cap for female panel mount connector 08 3110 000 000

Specifications of cable 4 (Signal) + 3+PE (Power) 11 Comparable AWG conductors see technical Information. 21

For the harshest environmental conditions

PICTURES: SHUTTERSTOCK, FOTOLIA, ISTOCK, STEFFEN WALTER STUDIOS

Franz Binder GmbH & Co. Elektrische Bauelemente KG [email protected] www.binder-connector.de Specifications may be changed without notice, errors excepted. AGB: www.binder-connector.com/en/terms