Catalog excerpts
Medical Technologies Matrix Switcher MTS800A Video Management System Installer User's Guide Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely.
Open the catalog to page 1Introduction . . . . . . . . . . . . . . . . . . Symbol Definitions . . . . . . . . . . . . . . Safety Instructions . . . . . . . . . . . . . . Caution . . . . . . . . . . . . . . . . . . . . . Parts . . . . . . . . . . . . . . . . . . . . . . . MTS800A Sample System Configuration Connectors . . . . . . . . . . . . . . . . . . . Connect Input Video Sources . . . . . . . Connect Output Video Destinations . . . Connect Power . . . . . . . . . . . . . . . . Connect a Remote Control Device . . . . Methods of Operation . . . . . . . . . . . . Streaming Setup . . . . . . . . . . . . . . . General...
Open the catalog to page 2ENTER INPUT MTS800A is an all-in-one medical device switcher solution that manages several independent input/ output systems typically found in a surgical environment. MTS800A uses a stand alone PC, or a tablet PC with touch screen user interface to control video switching. Streaming is also available, and live preview of the active video signal can be seen on the controlling PC. As a single location that controls a variety of medical OR video systems, MTS800A brings efficiency and simplicity to the busy operating room during surgical procedures. Supported video includes: • 8x8 DVI-D...
Open the catalog to page 3The following symbols appear on the product, its labeling, or the product packing. Each symbol carries a special definition, as defined below:
Open the catalog to page 4Please read the following safety instructions as they are designed to prevent damage to property and harm to the user. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Important to read and understand at all times Disconnect the plus from outlet Grounding to prevent an electrical shock Power Use only a proper plug and voltage. Improper power may cause electric shock or equipment damage. To avoid the risk of electric shock, this equipment must only be connected to a power supply with protective grounding. Installation Do...
Open the catalog to page 5RISK OF ELECTRICAL SHOCK DO NOT OPEN This symbol alerts the user that important literature concerning the operation of this unit has been included. Therefore, it should be read carefully in order to avoid potential problems. This symbol warns the user that un-insulated voltage within the unit may have sufficient magnitude to cause electrical shock. Therefore, it is dangerous to make contact with any part inside the unit. To reduce the risk of electric shock, DO NOT remove cover (or back). There are no user serviceable parts inside. Refer servicing to qualified service personnel. To...
Open the catalog to page 6The hospital-grade plug for medical products intended for use in Denmark has DEMKO approval and is rated 13 amps at 250Vac. Plug is recommended for use in medical applications and specificationsare being added to the standard SB 107-2-D1. Plug mates with maker's Danish hospital-grade socket. Hospital sockets have slightly different shaped openings allowing only the hospital plug, not the standard Danish plug, to be inserted, to protect the AC circuit in specific medical settings. FCC WARNING : This equipment has been tested and found to comply with the limits of a Class B digital...
Open the catalog to page 7Follow local governing ordinances and recycling plans regarding the recycling or disposal of this equipment. Servicing Do notattempt to service the system yourselfas opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to qualified service personnel. Unplug the system from its power sourceand refer servicing to qualified personnel under the following conditions: - If the power cord or plug is damaged or frayed. - If liquid has been spilled into the system. - If objects have fallen into the system. - If the system...
Open the catalog to page 8Package Contents Verify that you received all components of your respective package. Inspect each component and verify that none of the components have been tampered with in any way.
Open the catalog to page 9MTS800A Sample System Configuration Wall Mount Boom or Stand Monitors Tablet with Control Interface Video Sources to be Switched
Open the catalog to page 10MTS800A is capable of handling 20 input video source signals. Many applications require fewer inputs. Each unique situation will determine the number and type of input video sources that will be connected to MTS800A. Never use this system with damaged cords. Keep all cords away from areas where they may cause tripping. Output video signals from medical equipment. Connect video sources to input ports on the back panel of MTS800A. Input signal choices are: 4 - C-Video 4 - RGB 8 - DVI-D 4 - SD/HD/3G-SDI Signals being switched must be the same type. Example: DVI in and DVI out is supported, DVI...
Open the catalog to page 12After incoming video signals are connected to MTS800A, they are switched and sent out, or output, to a destination. A destination is usually a surgical display monitor. There are 20 output ports that correspond to the video inputs. Additional output ports are available for video stream preview and DVI-connected monitor preview of the active video signal. TZZT These output ports are for video stream preview and DVI-connected monitor preview of the active video signal. Connect video destinations to output ports on the back panel of MTS800A. Output signal choices are: 4 - C-Video 4 - RGB 8 -...
Open the catalog to page 13Only use the specified plug and voltage. Power requirements are: AC 100-240V/ 50~60Hz, 2A(max). Use the supplied 6 ft. hospital grade AC power cord. Improper power may cause electric shock or equipment damage. To avoid the risk of electric shock, this equipment must only be connected to a power supply with protective grounding. Precaution Turn off system power switch before making any video connection modifications.
Open the catalog to page 14Connect A Remote Control Device The preferred way to manipulate video signals with MTS800A is by connecting a remote control device, such as a touch screen tablet. This allows use of the graphic user interface that has been designed for the features available with MTS800A. Touch screen control device
Open the catalog to page 15All FSN Medical Technologies catalogs and technical brochures
-
FM-A5504DS;FM-A5504DG
2 Pages
-
MSV 2
2 Pages
-
Vy-Net2
2 Pages
-
IPS740DS IPS740DG
2 Pages
-
21.5” HD LED Medical Display
2 Pages
-
FM-D5801DV
2 Pages
-
FM·D5801DV
2 Pages
-
FM·C5501DV, FM·C5501DG
2 Pages
-
FS-L3202D - 2018
2 Pages
-
FS-L2702DT
2 Pages
-
FS-L2702D
2 Pages
-
FS-P2607D
2 Pages
-
FM·B2702D, FM·B2702DG
2 Pages
-
FM-A2701D FM-A2701DS
2 Pages
-
FM-C5501DV FM-C5501DG
2 Pages
-
DSP
1 Pages
-
IPS710A
2 Pages
-
FS-P2604D
2 Pages
-
FS-P2404D
2 Pages
-
FS-L2701D
2 Pages
-
WirelessOR - WIS1000A
2 Pages
-
ControlOR - IPS1000A
2 Pages
-
RecordOR - IPS700A
2 Pages
-
ConvertOR - IPS500A
1 Pages
-
4KUHD FS-L5502D
2 Pages
-
4KUHD FS-P3101D
2 Pages
-
MultiTouch FS-S4601DT
2 Pages
-
MultiTouch FS-L2701DT
2 Pages
-
FS-P2603D
2 Pages
-
FS-P2602D
2 Pages
-
FS-P2601D
2 Pages
-
FS-Y1901D
2 Pages
Archived catalogs
-
FS-L3202D
2 Pages