Shower fitments technical info
1Pages

Technical information Thermostatic TMV2 levered shower Thermostatic TMV3 levered shower Electric Care shower • Dual control – flow and temperature are controlled separately, giving accurate control of both • Thermostatic cartridge maintains showering temperature to +/- 1ºC by compensating for changes in the incoming water temperature and pressure • Automatic shut off in the event of hot or cold water supply failure, thus reducing the risk of any injury • Factory-set to a maximum of 38ºC to eliminate the ability to select an unsafe temperature • Utilises unique fast fit system – wall mount • Supplied with 1.5m hose, riser rail, hose retainer and single function handset with rub clean nozzles • Chrome plated to BS EN 248 • Product supplied with 2 x 7 litre per minute flow regulators, one fitted in each inlet to control water flow when fitted to instantaneous water heaters (combination boilers). These can be removed to suit different water delivery systems, i.e. low pressure gravity systems • Dual control – flow and temperature are controlled separately, giving accurate control of both • Thermostatic cartridge maintains showering temperature to +/- 1ºC by compensating for changes in the incoming water temperature and pressure • Automatic shut off in the event of hot or cold water supply failure, thus reducing the risk of any injury • Factory-set to a maximum of 38ºC to eliminate the ability to select an unsafe temperature • Adjustable maximum stop temperature between 35ºC-45ºC • Suitable for either high or low pressure systems • Lever controls • Supplied with 1.25m hose, riser rail, hose retainer and multi function handset with rub clean nozzles • BEAB Care Mark: adjustable max. temperature: 38°C, 41°C or 43°C • WRAS, RNIB, Kite Mark, CE approved • Timed shutdown to reduce water consumption (5-30 minutes) • Tri-thermostatic temperature control system • Waste pump connectivity (flow sensor maintenance not req.) • 2.0m hose & extended riser rail • 5 pattern shower head includes ‘delicate skin setting’ • Oversized start-stop button for users with reduced dexterity/vision • Audible control option - ideal for the visually impaired • Phased shutdown - reduces limescale and flushes hot water from the hose and shower-head after use Specification Chrome finish - brass body construction W.R.A.S. cert 1001025 Temperature setting range 38-46ºC Flow rate 6.5 Ltrs at 0.2 bar Flow rate 16.5 Ltrs at 1 bar Plumbing connections Hot – 15mm compression Cold – 15mm compression W.R.A.S compliant shower Chrome finish – brass body construction Backplate, cover, controls, showerhead – ABS. Conforms to NHS Estates Model Engineering Specification DO8 W.R.A.S compliant shower TMV3 BC447/1208 BS EN 111, 1287 Temperature setting range 35-47ºC Minimum running pressure/flow 0.5 bar* @ 8 l/min Maximum static pressure 10 bar Automatic shutdown Plumbing connections Temperature setting range 35-45ºC Flow rate 8 Ltrs at 0.1 bar Outlet - ½” BSP male thread Plumbing connections W.R.A.S compliant shower Supply source : mains pressure cold water only W.R.A.S compliant shower Minimum inlet temperature 2°C Water entry points rising, falling, back Pipe inlet centres Outlet connection Water – right: top, bottom back, bottom Cable – right: top, top back, bottom Minimum running pressure/flow Maximum running pressure Maximum static pressure Open outlet flow rate Nominal power rating at 240V 8.5kW – (40A MCB rating) 9.5kW – (40A MCB rating) Maximum flow with flow limiters Entry points Nominal power rating at 230V 7.8kW – (40A MCB rating) 8.7kW – (40A MCB rating) Mains electric supply (via double pole switch) * Recommended minimum running pressure and flow at the shower inlet 100kPa (1 b