BLooK™
10Pages

BLooKTM LED transilluminator Catalog number: BK001 BLooKTM is an extraordinary blue light LED transilluminator for the detection of nucleic acids or protein under non-UV conditions. The wavelength of the special blue LED lights is 470 nm (fig 1), hence no damage to your nucleic acids or protein. Since UV is not used, there is no need for any special personal eye or skin protection. The blue LED lights are arranged under the viewing area (200 × 120 mm). An amber filter, on hinges, is lowered into position once your gel is mounted. The stained gel is now ready for observation. This instrument...

(A) Power Cord: Used to connect the BLooK™ port with the power socket. (C) Gel-Cutting Knife: Cut out the target from the gel for further experiment. (D) Replacement Blade: Used as the new blade.

Amber filter The upper panel is the amber filter used to observe the gel upon being lowered in position. Light source The light source is located below and projects upward from the bottom. Please first lower the amber filter in position when in use for preventing the eye damage. Power inlet is used for connecting the power cord. ON/OFF button is used for switching on and off the power. Ventilation holes are located on the same side and enable the heat, which is generated when power is on, to be exhausted. Dented holder A long, dented holder, which is located close to the operator, is used...

2. Connect the power cord and the socket. 3. Open the amber lid. Note: Please open amber lid carefully by two hands. 4. Place the gel on glass area. Note: The automatic power shut-off option at 5 minutes. Once the LED lights are off, wait for 3 minutes, and then 　　　press the power button again to re-turn on the light. 5. Close the amber lid above the gel. 6. Press ON/OFF switch to ON mode. 7. Now the fluorescent samples can be viewed or cut. Note: For cutting fluorescent samples out of the gel, please lift the lid to access the gel. 8. When finished, turn the transilluminator off. 9. Clean...

Troubleshooting Refer to the table below to troubleshoot problems that you may encounter when using with the BLooK™ LED transilluminator. Note: Please, read the installation instruction carefully before installing the BLooKTM LED transilluminator. This instrument is intended for clinical and research laboratory use and it must be operated only by specialized personnel aware of the potential risks associated with the chemical and biological agents normally used with this unit. This instrument is meant for use only by specialized personnel that know the health risks associated with blue light...

Maintenance and Repair Cleaning and Maintenance The transilluminator should be damply wiped off with a soft cotton cloth. The cloth should not be too wet. Do not use aggressive cleaning detergents or solvents. After use of the transilluminator, we recommend to wipe off the frame and the filter glass with a damp cloth. Take care that the cloth is not soaked with scrubbing or corrosive detergents as this could damage the filter glass. We suggest using alcohol, glass cleaners or similar mild detergents. Pay attention to wearing appropriate gloves when cleaning areas (as the filter plate of the...

REGULATORY NOTICE IMPORTANT: This GeneDireX, Inc. instrument is designed and certified to meet safety standards. Certified products are safe to use when operated in accordance with the instruction manual. This instrument should not be modified or altered in any way. Alteration of this instrument will: 1. Void the manufacturer’s warranty 2. Void the safety and EMC certification 3. Create a potential safety hazard GeneDireX, Inc. is not responsible for any injury or damage caused by the use of this instrument for purposes other than those for which it is intended, or by modifications of the...

Caution The BLooK TM LED transilluminator is classified as a Class 2 LED product, which is indicated by the symbol to the left, radiation when open, do not stare into the beam Safety Information The BLooKTM LED transilluminator is an electrical device. Never touch the power cord or outlet with wet hands. Do not use this device in damp areas or while standing on damp floors. Do not attempt to open the BLooKTM LED transilluminator. The BLooKTM LED transilluminator should be used with the supplied power cord. Only these power cords should be used to power the device. Attach the power cord to...

Made in TAIWAN CHINA Patent: CN203115668U TAIWAN Patent: M449283