Neonatal Incubator - OGB Polytrend
12Pages

Polytrend Polytrend Neonatal Incubators

Polytrend The best technology for Sub-Intensive and Intensive Care For the last 60 years GINEVRI srl has been designing and manufacturing neonatal incubators which are, and always have been, distinguished by their innovative technical solutions and for their cutting edge performance, in addition to their reliability and extreme simplicity of use, cleaning and sterilization. In summary: I UNBREAKABLE & LIGHT WEIGHT of the hood, base and other main components all made in POLYCARBONATE; I GREATLY REDUCED RISK OF INFECTION, with the capacity to totally dismantle the incubator for complete...

Control Panel - simple and intuitively evident The control panel, equipped with a LCD display screen to show all the parameters readings and settings is completely microprocessor The practical rotational "encoder" on the control panel facilitates the setting of all the different parameters and access to all the various display screens which include: ■ Trend: air temperature, skin temperature, peripheral skin temperature, difference between skin and peripheral temperature, difference between air and skin temperature, relative humidity, weight, oxygen concentration, heart rate and The...

Polytrend Practical Qualities The awareness that medical treatment and care equipment, beyond the fundamental protection and promotion of the patient’s health, must also, when possible, simplify the medical care operator’s life and not complicate it has guided the research and design for the assembly of our incubators. In fact, all the functions and procedures which care personnel need to carry out in the course of neonatal assistance, from cleaning and disinfection after use to technical assistance, have been designed to be straightforward, practical and easy to carry out. The wires for...

OPERATING: The external ambient air, eventually enriched with oxygen, enters the incubator passing through a high capacity micro-filter (less than 0,5 μm) located on the base. A special fun sucks air from outside (with oxygen if necessary) and pushes it into the heating chamber and air, after having passed through the humidifier, flows in the hood through the specially provided slits without causing dangerous turbulence around the newborn. The best solution, scientifically approved is the one applied on our incubators, where air required for the elimination of CO2 enters and exits from the...

Polytrend An Innovative and Practical Hood The hood is made from polycarbonate in a single piece. It has two main doors for total opening; it has six access portholes with soundproof opening and equipped with gaskets and sleeves to prevent leak of temperature and humidity, when they are opened. In addition, in the hood itself there are pre-made channels for passing the wires and tubes necessary to connect the little patient to external medical devices. There are several possible openings: • Upwards with alloy hinge; • Downwards and Upwards with alloy hinge (optional); • Downwards with...

Polytrend Humidification and Oxygenation Humidification All incubators in the POLYTREND series include a standard humidifier. This is made up of a basin for keeping water and a device to manually adjust the humidity level. Both the basin and the above mentioned unit are made of pressure stamped polycarbonate. The basin is transparent and can be easily taken out to allow the water to be changed, cleaning or sterilization, without moving the patient from inside the incubator. The models which are equipped with humidity servo-control use a peristaltic pump and a heater to withdraw water from a...

Polytrend Patient Tray The PATIENT TRAY is: Made of polycarbonate in one single piece; I Wide with the mattress; I Perfectly connected and with all surfaces smooth; I Unbreakable, anti-fire, self-extinguishing; I Permits to measure the patient both in centimeters and inches; I Easily removed to allow for complete thorough cleaning and sterilization; The entire perimeter permits the flow of hot air which, in this way, creates not only a perfect micro climate circulation but also a protective barrier for the little patient when the doors are open; Supported by a special Smooth Tilt device for...

Polytrend Trolleys, Accessories and Consumables The trolleys, with their innovative and ergonomic design, are made of treated stainless steel. The base’s side panels are made of polycarbonate and the handles are fabricated with stainless steel also, resistant to inevitable bumps and scrapes. On both the short Microclimate hood with bed sheet sides sliding service trays can be equipped. Service drawers can also be equipped below the trolley. The trolley can be either height adjustable by a foot pedal control, which can also be installed on both sides, or fixed height. Skin probe Remote...

Polytrend Technical Specifications MODEL CE MARK MOBILE OR TRANSPORT TEMPERATURE CONTROL Air: Range (increments): Skin: Range (increments): TEMPERATURE DISPLAY Air temp.: Skin temp.: Peripheric skin temp.: TRENDS VISUALIZATION RELATIVE HUMIDITY DISPLAY RELATIVE HUMIDITY CONTROL OXYGEN CONCENTRATION DISPLAY OXYGEN CONCENTRATION CONTROL O2 inlet ports/ controllers: Servo control (OPTIONAL): ALARMS - VISIBLE AND ACOUSTIC Low heart rate High heart rate Low SpO2 High SpO2 High air temperature Low air temperature High skin temperature Low skin temperature Fan failure Air probe failure Skin probe...

Quality System ISO 9001:2008 ISO 13485:2012 The specifications in this catalogue are indicative. The company GINEVRI srl reserves the right to make changes, without further notice, to the products described within this catalogue in order to improve reliability, function or design. Quality for life GINEVRI srl Via Cancelliera, 25/b 00041 Albano Laziale (Rome) - Italy Tel.: +39 06 93459 330 Fax: +39 06 93 459 393 e-mail: export@ginevri.com www.ginevri.com Authorized Distributor