Drilling Protocol

Product catalog summary

Drilling Protocol Overview
This document provides a comprehensive overview of the drilling protocols for the Hahn™ Tapered Implant system, detailing specifications for drill sizes, recommended speeds, and procedural guidelines to ensure successful implant placement.

Recommended Drilling Speeds

Twist/Shaping Drills: 800-1200 RPM
Screw Tap: Do not exceed 25 RPM

Consult the Instructions for Use for detailed guidance.

Drilling Procedures

Initial Drilling: Start with a Twist Drill Ø1.5 x 8 mm.
Sequential Drilling: Progress through specified drill sizes to achieve the desired osteotomy depth.
Final Drilling: Use the final drill size corresponding to the implant length.
Optional Dense Bone Screw Tap: Use Ø3.0 mm or Ø3.5 mm as needed.

Implant Sizes and Codes
Implants are available in various diameters and lengths, each with a specific description code for identification and ordering.

Critical Guidelines

Ensure all surgical instruments are available before surgery.
Increase osteotomy depth sequentially, starting with shorter drill lengths.
Do not use drills exceeding the diameter or length of the prescribed implant.

Conclusion
This protocol ensures precise and safe implant placement by adhering to recommended speeds and sequential drilling procedures. Always follow the manufacturer's guidelines and consult the Instructions for Use for comprehensive instructions.

Specifications
Drill diameters and lengths are specified for different implant sizes, with each component associated with a unique description code for identification.

Procedures
Ensure all surgical instruments are available before surgery, increase osteotomy depth sequentially, and do not use drills that exceed the diameter or length of the prescribed implant.

Drilling Protocols
Protocols are provided for various implant sizes, detailing the sequence of twist and shaping drills to be used, with optional dense bone screw taps and parallel pins included for specific protocols.

Equipment Description Codes
Each drill and implant component is listed with a specific code for identification.

Additional Notes
All procedures and equipment use are by prescription only. Consult the Instructions for Use for detailed guidance.

Catalog excerpts

Drilling Protocol (Ø3.0 x 11.5 mm) RECOMMENDED DRILLING SPEEDS Twist/Shaping Drills: 800-1200 RPM Screw Tap: Do not exceed 25 RPM Final Drill Twist Drill Ø2.8/2.4 x 11.5 mm Optional Dense Bone Screw Tap Ø3.0 mm Implant Driver Ø3.0 Long Hahn™ Tapered Implant Ø3.0 x 11.5 mm Ensure all surgical instruments are available prior to surgery. Osteotomy depth may be increased sequentially, beginning with shorter drill lengths, provided sufficient depth is achieved with the final drill. Do not use any drill that exceeds the diameter or length of the prescribed

Open the catalog to page 1

Implant Driver Ø3.0 Long

Open the catalog to page 2

Drilling Protocol (Ø3.0 x 13 mm) RECOMMENDED DRILLING SPEEDS Twist/Shaping Drills: 800-1200 RPM Screw Tap: Do not exceed 25 RPM Final Drill Twist Drill Ø2.8/2.4 x 13 mm Optional Dense Bone Screw Tap Ø3.0 mm Implant Driver Ø3.0 Long Hahn™ Tapered Implant Ø3.0 x 13 mm Ensure all surgical instruments are available prior to surgery. Osteotomy depth may be increased sequentially, beginning with shorter drill lengths, provided sufficient depth is achieved with the final drill. Do not use any drill that exceeds the diameter or length of the prescribed

Open the catalog to page 3

Implant Driver Ø3.0 Long

Open the catalog to page 4

Drilling Protocol (Ø3.0 x 16 mm) RECOMMENDED DRILLING SPEEDS Twist/Shaping Drills: 800-1200 RPM Screw Tap: Do not exceed 25 RPM Final Drill Twist Drill Ø2.8/2.4 x 16 mm Optional Dense Bone Screw Tap Ø3.0 mm Implant Driver Ø3.0 Long Hahn™ Tapered Implant Ø3.0 x 16 mm Ensure all surgical instruments are available prior to surgery. Osteotomy depth may be increased sequentially, beginning with shorter drill lengths, provided sufficient depth is achieved with the final drill. Do not use any drill that exceeds the diameter or length of the prescribed

Open the catalog to page 5

Implant Driver Ø3.0 Long

Open the catalog to page 6

Drilling Protocol (Ø3.5 x 8 mm) RECOMMENDED DRILLING SPEEDS Twist/Shaping Drills: 800-1200 RPM Screw Tap: Do not exceed 25 RPM Final Drill Shaping Drill Ø3.5 x 8 mm Optional Dense Bone Screw Tap Ø3.5 mm Implant Driver Ø3.5/4.3 Long/Short Hahn™ Tapered Implant Ø3.5 x 8 mm Ensure all surgical instruments are available prior to surgery. Osteotomy depth may be increased sequentially, beginning with shorter drill lengths, provided sufficient depth is achieved with the final drill. Do not use any drill that exceeds the diameter or length of the prescribed

Open the catalog to page 7