VersiON MB1000 The lift MB1000 has a lifting height up to 1000 mm and is designed for the use by wheelchair drivers. The platform size of 830 x 1650 mm allowes an additional companion to drive with the wheelchair user. VersiON MB1300 The lift MB1300 is the larger version of the MB1000. The difference: More lifting height of up to 1280 mm and a larger platform of 900 x 2000 mm. Naturally absolutely wheelchair accessible in public areas with plenty of space. Individual wishes? Contact us! Lift width: 1190/1310 mm lift tYPe liftiNG HeiGHt Revision 09/2018 - Subject to technical changes HerKules liftwerK made in Germany Herkules liftwerk GmbH industriestraße 3 34260 Kaufungen tel 0561 9539970 fax 0561 95399799 www.liftwerk.de Leben. Unabhängig. Leben. Unabhängig.

LiFT mB1000 & mB1300 fast, easy, everywhere 4 Waterproof sensor buttons with vandalism protection class IK08 and key lock reADY fOr use iN less tHAN 60 seCONDs The lift MB1000/1300 solves problems fast and efficient. With those lifts no physical provision is needed. Everything it takes is an even surface. Wether on exhibitions, events or on-stage appearances - the lift is delivered, put down and connected to the normal 230V power supply, yet it is ready for use. The lifts have a vast weather resistance and are made of high quality material, which porvides that the lift stays station and an automatic...

Lifting heights: When installed on ground: 1000 mm When installed in a pit of 55 mm: 945 mm The installation ground for the MB1000 must be flat and horizontal. The surface load is max. 5 kN/m2. Power supply: 230 V / 50 Hz, 16 A Maximum power consumption: 0,3 kW Lifting speed: 1.5 cm/s Safety celarances to other parts next to the MB1000: >100 mm Maximum gap width between the platform and the upper exit: 20 mm The MB1000 is only usable with straight passage. Depending on the actual lifting height, fall protection should be installed at the upper station. We recommend our MB door for this. IF NOT...

Pit depth minimum 55mm for access at ground level. Width of the pit only applies in public areas when there is no side access to the pit. With side access, additional 10 cm pit width should be added to each accessible side. Electrical connection ideally from rear left (seen from lower entrance). Alternatively, the power supply could come out of the ground so there would be no visib e wire. When the door for upper station is used as fall protection, we recommend to lead ductwork to the lift from underneath so there is no visible wire. When call-buttons are used, we recommend to lead ductwork from...

Lifting heights: When installed on ground: 1285 mm When installed in a bit of 70 mm: 1215 mm The installation ground for the MB 1300 must be flat and horizontal. The surface load is max. 5 kN/m2. Power supply: 230 V / 50 Hz, 16 A Maximum power consumption: 0,3 kW Lifting speed: 1.5 cm/s Safety clearances to other parts next to the MB1300: >100 mm Maximum gap width between the platform and the upper exit: 20 mm The MB 1300 is only usable with straight passage. Depending on the actual lifting height, fall protection should be installed at the upper station. We recommend our MB door for this. IF...

Pit depth minimum 70 mm for access at ground level. Electrical connection ideally from rear left (seen from lower entrance). Alternatively, the power supply could come out of the ground so there would be no visib e wire. When the door for upper station is used as fall protection, we recommend to lead a ductwork to the lift from underneath so there is no visible wire. When call-buttons are used, we recommend to lead a ductwork from the buttons to the lift from underneath so there is no visible wire.

WENN NICHT ANDERS DEFINIERT: BEMASSUNGEN SIND IN MILLIMETER OBERFLACHENBESCHAFFENHEIT: TOLERANZEN: LINEAR: WINKEL: ENTGRATEN UNDSCHARFE KANTEN BRECHEN ZEICHNUNG NICHT SKALIEREN NAME GEZEICHNET Bartsch GEPRUFT GENEHMIGT PRODUKTION QUALITAT

WENN NICHT ANDERS DEFINIERT: BEMASSUNGEN SIND IN MILLIMETER OBERFLACHENBESCHAFFENHEIT: TOLERANZEN: LINEAR: WINKEL: ENTGRATEN UNDSCHARFE KANTEN BRECHEN ZEICHNUNG NICHT SKALIEREN NAME gezeichnet Bartsch GEPRUFT GENEHMIGT PRODUKTION QUALITAT

B ENTGRATEN UND SCHARFE KANTEN BRECHEN WENN NICHT ANDERS DEFINIERT: OBERFLÄCHENGÜTE: BEMASSUNGEN SIND IN MILLIMETER OBERFLÄCHENBESCHAFFENHEIT: TOLERANZEN: LINEAR: WINKEL: NAME Massblatt Aussenruf AP mit Schlüssel ZEICHNUNG NICHT SKALIEREN PRODUKTION WERKSTOFF:

B ENTGRATEN UND SCHARFE KANTEN BRECHEN WENN NICHT ANDERS DEFINIERT: OBERFLÄCHENGÜTE: BEMASSUNGEN SIND IN MILLIMETER OBERFLÄCHENBESCHAFFENHEIT: TOLERANZEN: LINEAR: WINKEL: NAME Massblatt Aussenruf UP mit Schlüssel ZEICHNUNG NICHT SKALIEREN PRODUKTION WERKSTOFF:

B ENTGRATEN UND SCHARFE KANTEN BRECHEN WENN NICHT ANDERS DEFINIERT: OBERFLÄCHENGÜTE: BEMASSUNGEN SIND IN MILLIMETER OBERFLÄCHENBESCHAFFENHEIT: TOLERANZEN: LINEAR: WINKEL: NAME Massblatt Aussenruf AP ohne Schlüssel ZEICHNUNG NICHT SKALIEREN PRODUKTION WERKSTOFF:

B ENTGRATEN UND SCHARFE KANTEN BRECHEN WENN NICHT ANDERS DEFINIERT: OBERFLÄCHENGÜTE: BEMASSUNGEN SIND IN MILLIMETER OBERFLÄCHENBESCHAFFENHEIT: TOLERANZEN: LINEAR: WINKEL: NAME Massblatt Aussenruf UP ohne Schlüssel ZEICHNUNG NICHT SKALIEREN PRODUKTION WERKSTOFF:

WENN NICHT ANDERS DEFINIERT: BEMASSUNGEN SIND IN MILLIMETER OBERFLACHENBESCHAFFENHEIT: TOLERANZEN: LINEAR: WINKEL: