Catalogs >
Hill-Rom >
Integris® Light Solutions

Integris® Light Solutions
4Pages

Catalog excerpts

Hill-Rom® Lighting Systems for Patient Rooms Integris® Patient Light • Housing: Extruded aluminum body with die-cast end caps. Housing attached to mounted baseplate for wiring with integral swing hook. After wiring, housing swings closed; secured with countersunk fasteners. White urethane powder coat finished – 5-step pre-treatment; laboratory salt spray test: 1,000 hours. • Baseplate: 16 gauge CRS baseplate provided with six-point (36" and 48" housing) mounting holes and one wireway hole. • Lens: U.V. stabilized, high impact resistant, extruded linear DR/acrylic (50/50 blend). Smooth exterior, fluted interior. Nominal thickness .125". Lens securely positioned in body channels. • Electrical: Fluorescent electronic 120/277/347V ballasts high power factor (<10% THD). One ballast for upper compartment and one ballast for lower compartment standard. Circuits supplied with quick connects/disconnects. See Ordering Information for optional equipment. Lamps by others. • Installation: Standard six-point (36" and 48" housing) mounting. • Listings: UL and CUL Listed. Certified by independent lab to meet OSHPD seismic loading standard. Pre-approved by OSHPD for installation in California healthcare facilities. US Patent No. D527,131. • Safety: An Emergency Shut-Off switch will cut off power to the bed only receptacle when an IV pole or other equipment makes contact with the light. Reading/Ambient/Exam Wall Mount – Surface Nominal 5"x36" and 5"x48" Ordering Information H/R Model# Lamp Configuration Lamp Type PHR Hill-Rom Neutral MW Matte White MW/AMF Matte White Antimicrobial Finish Ballast Type Three Foot Lengths 25 F25T8 Four Foot Lengths 32 F32T8 IS* <10% THD Instant Start RS <10% THD Rapid Start *IS is standard, RS is optional Wiring Option 1 Wiring Option 2 Wiring Option 3 Wiring Option 4 Wiring Option 5 PCC (4 Position) (120V only) Locate in the center LVC Low Voltage Controller Note: PCC and LVC cannot be ordered together Note: Fuse Holder (FS) is Standard, not Optional Note: Emergency Shut-Off Switch (ES) is Standard, not Optional

Open the catalog to page 1

Hill-Rom® Lighting Systems for Patient Rooms Integris® Patient Light P005196A Dimensional Data Cross Section BACK VIEW EXAM Candlepower Distribution Exam/Reading Plan View Test Report Number: P200444P Candlepower Distribution READING Ambient Plan View Test Report Number: P200442P Lamps: Two 32 Watt T8 Candlepower Distribution Fixture Type Catalog Number Approved by Reading Plan View – 1' x 3' Calc Plane @ 45°, 47" AFF Test Report Number: P200445P Lamps: One 32 Watt T8 Project Information Hill-Rom P005196A BACK VIEW

Open the catalog to page 2

Lighting Systems for Patient Rooms Integris® Patient Light Wiring Options AMBIENT BALLAST 20 Amps MAX - SAFETY INTERLOCK (BED RECEPTACLE SAFETY SWITCH) READING BALLAST -<=ll READING LAMP HILLROM WIRING DIAGRAM 20 Amps MAX - SAFETY INTERLOCK (BED RECEPTACLE SAFETY SWITCH) HILLROM WIRING DIAGRAM

Open the catalog to page 3

Lighting Systems for Patient Rooms Integris® Patient Light Wiring Options INCOMING POWER READING BALLAST 20 Amps MAX - SAFETY INTERLOCK (BED RECEPTACLE SAFETY SWITCH) HILLROM WIRING DIAGRAM Hill-Rom reserves the right to make changes without notice in design, specifications and models. The only warranty Hill-Rom makes is the express written warranty extended on the sale or rental of its products. 3 2008 Hill-Rom Services, Inc. ALL RIGHTS RESERVED. USA 800-445-3730 Enhancing Outcomes for Patients and Their Caregivers.™

Open the catalog to page 4