FAS 16 mm FASPROP
4Pages

FAS 16 mm FASPROP Low flow proportional valve >> Cleaned for analytical applications >> High controllability in dosing gases in ml range >> Repeatable proportional characteristic over the lifetime >> High stability in closed loop control systems Technical features Medium: Compressed air, neutral gases Filtration: Orifice sizes 0,05 ... 0,3 mm: 5 µm filter already integrated Orifice sizes 0,5 mm: 5 µm filters can be integrated on request or to be placed before the valve Operation: Direct acting 2-way valve Normally closed Operating pressure: 0 ... 12 bar (0 ... 174 psi) Mounting: Cartridge Size: 16 mm Orifice: 0,05 ... 0,5 mm Life expectancy: ≥ 100 Mio. cycles Internal & external leakage: 10-3 mbar x l/s Electrical details Protection class (acc. to EN60529): IP51 Weight: 40 g (0.09 lbs) Ambient/media temperature: 0 ... +50 °C (32 ... 122°F) Air supply must be dry enough to avoid ice formation at temperatures below +2 °C (35°F). Materials: Body: Stainless steel Internal parts in contact with media: Stainless steel Seals in contact with media: FPM, FFPM Manifolds Contact your local fluid control specialist for information about our manifolding capabilities which include laminated polymer manifolds. Following options on request Seal in contact with media Power consumption: Operating pressure Electrical connection: Flow rate range Electrical insulation: Internal & external leakage Insulation class: Electrical connection Technical data - Standard models Symbol Seal Material Flow range (Stdl/min) Technical data - Standard models Valve orifice (mm) 0,05 ... 0,1 Current for maximum flow [nominal] (mA) * Continuous maximum gas flow, ambient temperature +50°C Our policy is one of continued research and development. We therefore reserve the right to amend, without 4/15 en 6.6.015.01 notice, the specifications given in this document. (2014 - 6010b) © 2015 Fluid Autom

FAS 16 mm FASPROP Low flow proportional valve Additional information Typical flows vs. supply pressure Under the seat and zero back pressure Typical hysteresis at 10 bar (145 psi) Orifice sizes: 0,05 and 0,1 mm Stdl/min 1 0,9 Supply pressure Accessories Test manifold for cartridge version with G1/8 ports in stainless steel Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. (2014 - 6010b) © 2015 Fluid Automation S

FAS 16 mm FASPROP Low flow proportional valve FASPROP cartridge mounting Cartridge fitting with radial connection D170.0001 Dimensions in mm Projection/First angle O ring Ø4 x 1 Cable AWG 26 O ring Ø16 x 1,5 Sub-base Screw Torx M 2,5 x 6 Cartridge fitting with combined connection D170.0002 Cartridge fitting with axial connection D170.0003 Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this

FAS 16 mm FASPROP Low flow proportional valveFASPROP for vertical manifold mounting on request Manifold fitting D170.0004 Dimensions in mm Projection/First angle A-A H 'O' ring 04 x 1 [2 Cable AWG 26 [3 'O' ring 016 x 1,5 S Sub-base E Screw Torx M 2,5 x 6 Warning These products are intended for use in industrial compressed air and neutral gas systems only. Do not use these products where pressures and temperatures can exceed those listed under »Technical features«. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or...