video corpo cad

FLATPROP 16mm Direct acting proportional valve
3Pages

{{requestButtons}}

Catalog excerpts

FLATPROP 16mm Direct acting proportional valve - 1

FAS 16 mm FLATPROP Direct acting proportional valve > 2/2 NC proportional valve > High precision miniature proportional valve > Flat plunger and spring for frictionless operation > Highly repeatable with over 100 million cycles > Accurate control of flows ranging from a few ml/min to 80 l/min Technical features Medium: Air, oxygen or neutral gases Orifices: Orifice sizes 0.8 to 2.0 mm (0.03'' to 0.078'') Filtration: A filtration of 10 micrometer is required before the inlet for valves with an orifice size comprised between 0,8 to 2,0 mm Operation: Direct acting 2-way valve Normally closed Hysteresis: Typical: <10% of full scale current Cleanliness: Oxygen compatible Operating pressure: 0 ... 12 bar (0 ... 174 psi) Mounting: Cartridge Size: 16 mm Life expectancy: > 100 Mio. cycles Internal & external leakage: < 10-2 mbar l/s (~0.6 ml/min) at pmax Protection class (acc. to EN60529): IP51 Weight: < 50 g (0.11 lbs) Ambient/media temperature: +10 ... +50 °C (+50 ... +122°F) Materials: Body: Stainless steel only or stainless steel/brass PEEK (only when mounted on sub-based) Seal: FPM, NBR, EPDM Manifolds Contact your local fluid control specialist for information about our manifolding capabilities which include laminated polymer manifolds. Following options on request Other orifice size available Specific coils Wider temperature range OEM specification Lower leak rate Manifold mount Electrical details Voltage/frequency: See technical data -standard coils Power consumption See technical data -standard coils Electrical connection: 300 mm A WG24 flying leads Technical data - Standard models Technical data - Standard coils Valve Coil resistance at 20°C Current for maximum Voltage +20°C (+68°F) Power +20°C (+68°F) Max. required voltage orifice (+68°F) ± 3% [R20] flow [nominal] [nominal] [nominal] for max flow *1) Please refer to instruction K12M.0001 for recommendation on drive signals Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. (2016 - 6001c) © 2016 Fluid Automation Systems s.a.

Open the catalog to page 1
FLATPROP 16mm Direct acting proportional valve - 2

FAS 16 mm FLATPROP Direct acting proportional valve Additional information Typical flows vs. supply pressure Air, 20°C, without back pressure Hysteresis Typical curves for orifice sizes 0,8 mm and 1,6 mm Air, 20°C, without back pressure Supply pressure Note: Flow vs. supply pressure curves are for informative purposes only and shall be used only for the pre-selection of the orifice size. Preliminary testing is recommended to take into account all application specific requirements and to select the most adequate orifice. For further information contact your local fluidic specialist. Manifold...

Open the catalog to page 2
FLATPROP 16mm Direct acting proportional valve - 3

FAS 16 mm FLATPROP Direct acting proportional valve Dimensions in mm Projection/First angle Interface geometry see Cartridge fitting D120.0010 Warning These products are intended for use in air, oxygen and neutral gas systems only. Do not use these products where pressures and temperatures can exceed those listed under »Technical features«. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult IMI Precision Engineering, Fluid Automation Systems s.a. The...

Open the catalog to page 3

All Norgren FAS MEDIC SA catalogs and technical brochures

  1. CHIPPROP

    2 Pages

  2. PICOSOL MS

    2 Pages

  3. CHIPSOL MS

    3 Pages