MedMaster MPCNGX Testing, Listings, Certifications & Warranties Modern Multi-Function Sealed Enclosure Luminaire for the Patient Room Fixtures designed for use in healthcare facilities must satisfy a number of demanding lighting and environmental requirements. Applicable listings are shown below. Please refer to individual product specification sheets at www.kenall.com for the most up-to-date information. ETL— A product bearing the ETL Listed Mark is determined to have met the minimum requirements of prescribed product safety standards as certified by a Nationally Recognized Testing Laboratory (NTL). The mark also indicates that the manufacturer's production site conforms to a range of compliance measures and is subject to periodic follow-up inspections to verify continued conformance. IP64— Certified to IP64 per IEC60598 by a Nationally-Recognized Testing Laboratory (NRTL) ensures that the enclosure is dust-tight and protected against splashing water without any harmful effects. NSF— An NSF Listing denotes that the luminaire has been evaluated for corrosion resistance, cleanability and the ability of exposed material to withstand normal wear. This supports the infection control standards established by healthcare facilities as indicated that the luminaire is easy to sanitize. Healthcare Multi-Function Luminaires 10200 55th Street Kenosha, WI 53144 Tel: 262-891-9700 www.kenall.com ©2016 Kenall Mfg. Co. All rights reserved. L10071-050916 LED 5-Year Warranty Kenall’s LED products are warranted by Kenall to be free of defects in workmanship and materials for a period of one (1) year from the date of invoice. Kenall warrants LED lamps and internal power regulation components for a period of five (5) years from the date of invoice against defects in materials and workmanship that result in a fixture depreciation of 30% or greater. Lumen depreciation is compared to the published lumen output of the product on the date of manufacture per IESNA LM-79 reporting procedures. Normal accumulation of particulates on the optical surfaces shall not be factored into the lumen depreciation. Low Voltage Controller for Multi-Function Luminaires A Low Voltage Controller is a device that allows low voltage control of line voltage luminaries. Kenall’s low voltage controller is a programmed interface module designed to operate up to three separate loads by the closure of low voltage momentary contact switches. These switches can be located on a patient hand-held pillow device, bed side rails, or a wall. Ordering Information Model Lamp Power Ambient/Reading Lamp Color Exam Lamp Color Driver Type Email: [email protected] 120 Volts 277 Volts Low Voltage Controller (consult factory for switching options) LVC Control with Dimming (consult factory) Anti-Microbial Finish on exposed surfaces The Kenall product shown on this page is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof.

MedMaster MPCNGX – The Next Generation of Multi-Function Patient Room LED Luminaires TM Everything from Soft Reading to Powerful Exam Light MPCNGX Performance Data Foot Candle Charts - 4000K (80 CRI) Calculations based on: Area: 12ft.×12ft. Ceiling Height: 8.5ft. Room Reflectance: 80/50/20 .90-LLF LED All calculations based on the 2'× 4' fixture. Consult specifications for 2'×2' performance data. Contemporary Design Meets Classic 2' × 2' and 2' × 4' Multi-Function Luminaires Kenall’s MedMaster MPCNGX multi-function overbed sealed enclosure luminaire is an accomplished multi-tasker. This modern,...

MedMaster MPCNGX – The Next Generation of Multi-Function Patient Room LED Luminaires TM Everything from Soft Reading to Powerful Exam Light MPCNGX Performance Data Foot Candle Charts - 4000K (80 CRI) Calculations based on: Area: 12ft.×12ft. Ceiling Height: 8.5ft. Room Reflectance: 80/50/20 .90-LLF LED All calculations based on the 2'× 4' fixture. Consult specifications for 2'×2' performance data. Contemporary Design Meets Classic 2' × 2' and 2' × 4' Multi-Function Luminaires Kenall’s MedMaster MPCNGX multi-function overbed sealed enclosure luminaire is an accomplished multi-tasker. This modern,...

MPCNGX Performance Data Foot Candle Charts - 4000K (80 CRI) Calculations based on: Area: 12ft.x12ft. Ceiling Height: 8.5ft. Room Reflectance: 80/50/20 .90-LLF LED All calculations based on the 2'x 4' fixture. Consult specifications for 2'x2' performance data. Ambient Function - Room Patient Bed I I MPCNGX Overbed Luminaire High Output Exam - Bed Surface Ambient Angled Reading IES Recommended Avg. fc MedMaster MPCNGX Avg. fc Produced MedMaster MPCNGX Avg. fc Produced High Output Exam IES Recommended Avg. fc MedMaster MPCNGX Avg. fc Produced MedMaster MPCNGX Avg. fc Produced * High-Power Exam mode...

Testing, Listings, Certifications & Warranties Fixtures designed for use in healthcare facilities must satisfy a number of demanding lighting and environmental requirements. Applicable listings are shown below. Please refer to individual product specification sheets at www.kenall.com for the most up-to-date information. ETL— A product bearing the ETL Listed Mark is determined to have met the minimum requirements of prescribed product safety standards as certified by a Nationally Recognized Testing Laboratory (NTL). The mark also indicates that the manufacturer's production site conforms to a...

MedMaster MPCNGX Testing, Listings, Certifications & Warranties Modern Multi-Function Sealed Enclosure Luminaire for the Patient Room Fixtures designed for use in healthcare facilities must satisfy a number of demanding lighting and environmental requirements. Applicable listings are shown below. Please refer to individual product specification sheets at www.kenall.com for the most up-to-date information. ETL— A product bearing the ETL Listed Mark is determined to have met the minimum requirements of prescribed product safety standards as certified by a Nationally Recognized Testing Laboratory...