Group: Danaher
Catalog excerpts
EM TRIM2 Specimen Trimming Device
Open the catalog to page 1Accurate, Safe, and Fast Sample Trimming Conventional trimming of embedded samples involves the use of razor blades and a great deal of skill by the ultramicrotomist. The shape of the block face and the straightness of the edges of the trimmed sample has a profound effect on the sectioning characteristics. Parallel edges top and bottom are a must. To achieve this quickly and safely is challenging and potentially hazardous with a razor blade especially on hard and brittle industrial materials. Important specimens can be destroyed by a minor inaccuracy in trimming. Perpendicular viewing...
Open the catalog to page 2With the EM TRIM2 a perfect pyramid and cutting face of both biological and industrial samples can be produced safely, rapidly and accurately within less than 60 seconds: >> With accurate, parallel edges >> With the angle of the pyramid sides set to user-preferred angle up to 60° >> With smooth and clean surfaces >> Any part of the sample can be targeted >> With perpendicular viewing of the embedded sample to determine its position for accurate milling >> With a 1 µm step rate and an ergonomically positioned feed hand wheel >> In any desired size from approximately 0.2 mm square upwards >>...
Open the catalog to page 3FUNCTION AND DESIGN, EASY TO USE The EM TRIM2 is a high speed milling system with an integrated stereo microscope and LED ring illuminator for trimming of biological and industrial samples prior to ultramicrotomy. A pivot arm and adjustment assembly holds the specimen carrier for optimum orientation. It can be used with either tungsten carbide or diamond milling tools. The area of interest can be centred and a flat block face milled onto the front face of the sample. For TEM and LM, the sample must then be trimmed to shape by adjusting the angle of the pivot arm and trimming the desired...
Open the catalog to page 4left: illumination for front face observation middle: perpendicular viewing with distance definition graticule right: illumination of the sample during milling Steps to trimming a pyramid EM TRIM2 Surface Quality The design of motor spindle in conjunction with the specially shaped tungsten carbide and diamond millers produce an excellent surface quality of the trimmed sample. Various diamond and tungsten carbide millers are available. EM TRIM2 with accurate sample removal With the ergonomically positioned feed hand wheel a step advance of 1 μm per click stop can be performed. The dynamic...
Open the catalog to page 5During operation the user is: >> Not in contact with dangerous components as the miller is located under a protective cover. >> Safe, as the instrument will not run unless the cover is closed. >> The spindle motor stops quickly as soon the cover is opened. >> To be easily accessible the miller ON/OFF switch is integrated into the control lever for the milling action. >> Hazardous waste, resin dust and fragments, which under razor blade trimming become airborne, are drawn into an extraction and filtration unit fitted with a Hepa-filter (optional). Waste connection to the extraction and...
Open the catalog to page 6FOR ADVANCED TRIMMING PERFORMANCE - EM RAPID In addition to the unique features of the EM TRIM2 the EM RAPID offers further opportunities to perform high end sample trimming. EM RAPID offers: Lever sample trimmed (front face observation) >> Variable milling speed between 300-20000 rpm allows settings to be adjusted for different materials. >> Pre-selection of the miller advance in steps of 0.5, 1, 10, 100 μm with each click stop of the hand wheel encoder. >> AUTO-Feed function allows safe and fast layer removal without operating the feed hand wheel. Embedded Si sample (perpendicular view)...
Open the catalog to page 7Copyright © by Leica Microsystems CMS GmbH, Wetzlar, Germany, 2017 · Subject to modifications LEICA and the Leica Logo are registered trademarks of Leica Microsystems IR GmbH. Leica Microsystems CMS GmbH | Ernst-Leitz-Strasse 17–37 | D-35578 Wetzlar (Germany) Tel. +49 (0) 6441 29-0 | F +49 (0) 6441 29-2599
Open the catalog to page 8All Leica Microsystems catalogs and technical brochures
-
M844 F40/F20
16 Pages
-
EnFocus
12 Pages
-
M822 F40 / F20
12 Pages
-
M320 for ENT
12 Pages
-
ARveo 8
16 Pages
-
M320 Dental Brochure
12 Pages
-
Emspira 3
4 Pages
-
Exalta
2 Pages
-
FLEXACAM C1
4 Pages
-
EM KMR3
8 Pages
-
EM UC7
16 Pages
-
EM RAPID
8 Pages
-
EM ICE
12 Pages
-
EM TXP
10 Pages
-
EM RES102
12 Pages
-
EM TIC 3X
16 Pages
-
TL4000 BFDF
16 Pages
-
F12 I floor stand
6 Pages
-
XL Stand
4 Pages
-
TL3000 Ergo & TL5000 Ergo
4 Pages
-
KL300 LED
8 Pages
-
LED1000
16 Pages
-
LED3000 BLI
20 Pages
-
LED5000 NVI
20 Pages
-
LED3000 NVI
20 Pages
-
LED3000 DI
20 Pages
-
LED5000 HDI
20 Pages
-
LED5000 CXI
20 Pages
-
LED2500
8 Pages
-
LED5000 MCI
20 Pages
-
LED3000 MCI
20 Pages
-
LED5000 SLI
20 Pages
-
LED3000 SLI
20 Pages
-
LED2000
8 Pages
-
LED5000 RL
20 Pages
-
LED3000 RL
20 Pages
-
MZ10 F
4 Pages
-
M165 FC
16 Pages
-
M205 FCA, M205 FA
16 Pages
-
M125 C, M165 C, M205 C, M205 A
12 Pages
-
A60 F, A60 S
16 Pages
-
M50, M60, M80
12 Pages
-
DVM6
16 Pages
-
HCS A
20 Pages
-
TCS SPE
20 Pages
-
DFC450 C
6 Pages
-
DFC295
6 Pages
-
MC170 HD
6 Pages
-
DFC3000 G
6 Pages
-
DMC4500
4 Pages
-
ICC50 W, ICC50 E
6 Pages
-
DFC7000 T, DFC7000 GT
4 Pages
-
DFC9000
2 Pages
-
IC90 E
6 Pages
-
DMC6200
8 Pages
-
DMC5400
8 Pages
-
SFL7000
4 Pages
-
EL6000
4 Pages
-
SFL100
4 Pages
-
SFL4000
4 Pages
-
DMi8 S Platform
2 Pages
-
THUNDER Imager Live Cell
2 Pages
-
DMi8 M / C / A
12 Pages
-
DM IL LED
12 Pages
-
DMi1
6 Pages
-
DM3 XL
7 Pages
-
FS M
4 Pages
-
FS C
4 Pages
-
FS CB
4 Pages
-
DM3000, DM3000 LED
16 Pages
-
DM750 M
12 Pages
-
DM750
12 Pages
-
DM500
12 Pages
-
DM300
8 Pages
-
DM12000 M
8 Pages
-
DM8000 M
8 Pages
-
DM1750 M
12 Pages
-
DM4 M, DM6 M
12 Pages
-
DM4 P, DM2700 P, DM750 P
12 Pages
-
DM2000, DM2000 LED
16 Pages
-
DM1000
16 Pages
-
DCM8
16 Pages
-
DM1000 LED
16 Pages
-
DM2500
16 Pages
-
DM4 B & DM6 B
16 Pages
-
DM6 M LIBS
2 Pages
-
S9 Series
12 Pages
-
Z6 APO
16 Pages
-
Z16 APO
16 Pages
-
Leica M530 OHX for ENT
4 Pages
-
M620 F20
8 Pages
-
M220 F12
8 Pages
-
Leica Application Suite X
4 Pages
-
Proveo 8
16 Pages
-
M525 F20
12 Pages
-
EnVisu Leica Handheld OCT
8 Pages
-
PROvido
8 Pages
-
Leica M530 OHX
16 Pages
-
Leica TCS SP8 STED 3X
24 Pages
-
Leica TCS SP8 Objective
24 Pages
-
Leica AOBS
16 Pages
-
Leica DMC2900
6 Pages
-
Leica DMshare
2 Pages
-
Leica_DMshare_ICC50-Flyer_en
2 Pages
-
Leica_DMshare_EC3-Flyer_en
2 Pages
-
Leica_SL801-Flyer
2 Pages
-
Leica_SCN400-Flyer_Clinical
2 Pages
-
DM2700 M
12 Pages
-
Leica_SR_GSD-Brochure
10 Pages
-
Leica_AF6000-Brochure
16 Pages
-
Leica motCorr-Flyer_EN
4 Pages
-
Leica TCS SP8-Flyer
2 Pages
-
Leica TCS SP8-Brochure
40 Pages
-
Leica TCS SP8 X-Flyer
2 Pages
-
Leica TCS SP8 STED-Flyer
2 Pages
-
Leica TCS SP8 HyD-Flyer
2 Pages