Catalog excerpts
Product data sheet Cleanroom ceiling system Line 100S Typ 3 not walkable Line 100S Typ 3 suspension parts / substructure 1. Line 100S Typ 3 metal ceiling panel 8. Vernier hanger upper section 9. Adjustable safety pin 54. C-profile runner made of steel 55. Vernier hanger lower section 56. Longitudinal connector 61. Intermediary runner 77. Vernier short hanger lower part 78. Self-drilling screw Fields of application: - Sterile technology / Pharmacy / Medical engineering Surface treatment technology Optics / Electronics / Precision mechanics Subject to change without notice. This document is intellectual property of Arnstorf based Lindner-Holding KGaA. It may neither be duplicated, exploited for profit, distributed for business purposes nor shown to any third parties without our approval. Please note that all details, schemes, pictures and dimensions shown in this catalogue are without commitment and might vary due to final project requirements. Especially all figures shown in inch are rough dimensions only. Our O&M manuals, Installation Recommendations, Product Specification Sheet, etc. and the installation of Lindner products are exclusively foreseen for persons with special metal ceiling knowledge. For safety reasons all others are not allowed to use Lindner’s products. Lindner ceilings must be installed as a complete system. Missing, wrong or by other products substituted components, additional loads by services for e.g. luminaries and not by Lindner approved anchors can cause failure of the complete ceiling system. Lindner ceilings are high-quality products for the interior only. All in our documents mentioned performances are subject to correct installation according to our company’s manuals and Standard Terms and Conditions. Lindner Reinraumtechnik GmbH, Postfach 11 06, 94420 Arnstorf, Germany, Tel. +49 (0)8723/20-0, Fax +49 (0)8723/20-23 55, www.Lindner-Group.com, Reinraumtechnik@Lindner-Group.co
Open the catalog to page 1
Product data sheet Line 100S Typ 3 not walkable General description Metal ceiling panels with coated surface, applied on suspended steel-grid, manufactured in accordance with European norms and TAIM-standard. 1. Metal ceiling panel Dimensions: Flush Lindner ceiling panel, length up to 3000mm, width up to 1200mm, manufactured of galvanized steel. Optional made of aluminum or stainless steel. Folds: Right-angled Perforation pattern: Suitable for cleanrooms flat Surface (I): Coil-coating with protection foil to protect from scratches, dirt and fingerprints whilst transport, storage and...
Open the catalog to page 2All Lindner Group catalogs and technical brochures
-
decke_br_lunar12 Pages
-
hkt_br_lindner_werblich20 Pages
-
mkt_br_stadia20 Pages
-
wand_br_life44 Pages
-
bt_br_tunnel8 Pages
-
decke_br_lindner_werblich24 Pages
-
decke_br_metalldeckensegel32 Pages
-
decke_br_streckmetalldecken40 Pages
-
decke_br_bandrasterdecken28 Pages
-
LMD/Plafotherm® Hook-On Ceilings32 Pages
-
LMD/Plafotherm® Baffle Ceilings20 Pages
-
LMD Cassette Ceilings20 Pages
-
Lindner Logic-OT / Life-OT3 Pages
-
Lindner OT sliding door5 Pages
-
Line 100S Typ 1 walkable2 Pages
-
Line 100S type 22 Pages
-
Lindner OT sliding door5 Pages
-
Lindner OT partition system3 Pages
-
Object door type „B“2 Pages
-
Clean Rooms20 Pages
-
Lindner Object door type ?E?2 Pages
-
Lindner Object door type ?A?2 Pages
-
Doors20 Pages
