Catalog excerpts
MCQ Gas Blender 100 Series 3 Channels Gas Mixer Revision 1.7 May 2015
Open the catalog to page 1Gas flow Dilutor & Gas flow Mixing System High Performance Digital Gas Blender for Mixing Gases and Calibration Routines Technical Data Sheet From this solution… Mixing and Blending up to 3 channels for non-aggressive gases. Ideal to make gas mixture for sensor or analyzer calibration. Fully digital. Needs No External Power & Control Unit. Needs No expensive and cumbersome tubing and fittings. Compact and transportable structure “Lab in a Box”. Accuracy for each channel: 1 % of set point (N2, 20°C, 101.325kPa (1 atm)) Range of Measurement: 0.01 sccm – 200 sccm (standard) (For each channel)...
Open the catalog to page 2High Performance Gas flow Dilutor & Gas flow Mixing System From this solution… The Gas Blender 100 series allows to simplify the common arrangement for gas delivery that usually consists of a control master and a series of Mass Flow Controllers (MFC), substituting the whole setup with a single compact box. The Gas Blender 100 series has three inputs from gas cylinder and a single channel for the blend output. Technical conept: airflow sensor GAS INLET from cylinders airflow sensor airflow sensor Microcontroller board power supply RS485 connection to other devices In the Gas Blender 100...
Open the catalog to page 3High Performance Gas flow Dilutor & Gas flow Mixing System Front Panel: FRONT PANEL Push-in connector The front panel of the Gas Blender 100 series contains four quick connector for the insertion of input tubes and for the output of the blend. Tubes with an external diameter of 6 mm can be inserted in the push-in connector. MCQ suggest to use tubes made of Tygon/Viton/PTFE/Stainless Steel/Polyurethane. Rear Panel: ON/OFF REAR PANEL Connection to other Gas Blender On the rear panel the are located the switch, the line power connection, the USB connection for the communication with a PC, and...
Open the catalog to page 4High Performance Gas flow Dilutor & Gas flow Mixing System Experimental arrangement: Doluition and mixing factors controlled by software Test chamber The gas cylinders can be simply connected to the push-in connectors through appropriate tubes, the output of the device must be connected to the test chamber or to the environment for custom applications where the blend is delivered. The mixing and dilution factors can be controlled by software, where the desired flow in each channel can be set and the actual gas flow is continuously displayed in a plot. Set-up for strong dilutions (*): 1 1...
Open the catalog to page 5High Performance Gas flow Dilutor & Gas flow Mixing System PERFORMANCE SPECIFICATION Accuracy (For each Channel) Repeatability Response Time for change of SetPoint 50 ms (For each Channel) Power Supply Operation Pressure Working Temperature MASS FLOW CONFIGURATION Materials Valve Steel/Brass, Viton Materials Tubes OPERATING SPECIFICATION Mass Flow Rates 0.01 sccm – 200 sccm (standard) FS: 0.01 sccm - 500 sccm (on request) Input channel USB PC interface 485 BUS with open proprietary protocol Function for future use. At the moment not active. Output Channel Output Signals Digital: BUS RS 485...
Open the catalog to page 6MCQGas Blender 100 Series High Performance Gas flow Dilutor & Gas flow Mixing System Via delle Quattro Fontane, 33
Open the catalog to page 7All MCQ Instruments catalogs and technical brochures
-
GB NANO 3
4 Pages
-
GB 15k
2 Pages
-
GB 2000
4 Pages
-
GB 3000
4 Pages
-
GB 4000
4 Pages
-
GB 6000
4 Pages
-
GB 100
4 Pages
-
GB 100 plus
4 Pages
-
SensorModule
7 Pages
-
Sensor Module
7 Pages
-
Gas Blender Advantages
4 Pages
Archived catalogs
-
Flow Board
11 Pages
-
Gas Blender 106 Series
4 Pages
-
Data acquisition board
4 Pages