Alexandrite Long Pulse Laser 755nm

www.miramhoo.com Alexandrite Long Pulse Laser 755nm-GENTAL MAX PRO 1. Appearance & Components 1. Appearance & Components (Noted： This photo is only considered as a reference; please reply with the real laser which may has differences at some details from the photo showed above. ) 1. Caster： to support and transport the equipment. 2. Handrail: 3. Right panel. 4. Monitor:

Alexandrite Long Pulse Laser 755nm-GENTAL MAX PRO to catch the headpiece. to conduct laser energy. to hold t the wires and cooling tubes. 11. Front panel. 12. Finger switch.

www.miramhoo.com Alexandrite Long Pulse Laser 755nm-GENTAL MAX PRO 2. Packing list Headpiece with cold wind cooling, spot-size 6-18mm

www.miramhoo.com Alexandrite Long Pulse Laser 755nm-GENTAL MAX PRO 2. Safety This article shows the details of safety when operation. The operator and technician must be certified after professional training of safety, know well the requirements of safety and steps to operate the laser. 1. Electric safety 1. Make sure the voltage of laser requiring will be adapted by local electricity supply. 2. 10 minutes after switching off and plug off the cable, only the maintenance can be started. No leave the laser without anyone taking care of by power on, or else injure will be happened to human or laser...

www.miramhoo.com Alexandrite Long Pulse Laser 755nm-GENTAL MAX PRO Water tank label Caution, no remove the covers.

www.miramhoo.com Alexandrite Long Pulse Laser 755nm-GENTAL MAX PRO 3. Specifications 1. Machine specification

www.miramhoo.com Alexandrite Long Pulse Laser 755nm-GENTAL MAX PRO Headpiece Candela Gentlemax Pro Control Monitor 10 inches Digital Real Color LCD Control system Single chip Headpiece Headpiece/spotsize 6-18mm spotsize with cold air coolilng Cooling Cooling system Water cooling water temperature Skin cooling internal air cooling machine optional cold air cooler Pulse width Pulse frequency Power system Power Capacitance capacity Laser board Lamp Fiber Size & Weight Size

1. Air quality： The system should work in a non-corrosive environment. Corrosive substances, such as acids, etc., may damage the surface of the wires and electronic equipment. Dust in the air should be kept to the minimum. Metal particles have a corrosive effect on the electronic device. 2. Temperature and humidity Working temperature： 10-30oC keep temperature： Working Relative Humidity：max 80% Storage relative humidity： Max 90% 3. Atmospheric pressure： 860hPA—1060hPA 4. Environmental requirements: Avoid the sunshine

1. Fiber support arm installation 1. Find the fiber support arm. 2. Fix arm tightly with screws. 3. Adjust the angle and screw it.

2. Fix fiber tightly with screw. insert into the fiber port 7. Fix fiber tightly with screw. 3. Prepare the finger switch and insert into the port. 8. Prepare the cooling tube and insert into the port. 9. Insert into the port deeply.

1. Find the water from water inlet 4.Connect foot-pedal and electric plug. 3. Open the overfall at the same time

1. Prepare the electric plug. 4.2. Water-cooling system Due to the generated huge heat of the xenon lamp when do treatment, and the treatment handle cooling the skin produce a lot of heat, so the machine needs to add a certain amount of pure water before work. Water added standard ： Distilled water or purified water （ avoid to use tap water or mineral water, otherwise it will seriously affect the working life of the machine and the cooling effect.） 1. 2. Water tank capacity：15L. the shortest period of replace cooling water: three months. Cooling water filling (see 4.1.3 step)： a. Water monitoring...

operating room should install air-conditioning equipment to ensure the temperature about 25oC before using the machine; otherwise the water temperature will be a sharp rise in a short time, which will not all shortens the working time of the machine , but also affect the service life of the machine. d. Water quality monitoring. Machine Built-in cooling water quality monitoring module. if the water is impurities, and water quality is bad, the machine will no longer monitor the water flow, suggesting that "water is not circulating." It should replace the cooling water in this time. e. water level...

5. Monitor Operations Guide This chapter describe the treatment handle of Alex. And Nd Yag laser system, the proposed treatment parameters and operation method. Please make sure to read in detail before using the product. 1. System operation 1.1. Start the machine。 1. Make sure the power cord is connected, insert the key, screw to the right, the start device inside the machine will start the machine, the user interface will light. 1. At this page, please select the wavelength related for treatment. YAG is 1064nm, Alex is 755nm. Now we click “YAG” for example.

4. The below page shows the main operating page for parameters adjustment. ( Figure 5.1.4).

a. press this button back to wavelength selection page. b. Press this button for applications reference, The page will show the page as below, At this page, the YAG Applications can be selected by, Hair Removal, Diffuse Redness, Vascular Lesions, and Facial Treatment. Or press page. c. Energy selection, At this page, the energy can be selected from

d. Pulse width selection, By this page, the pulse width can be selected from 10-100ms. e. Frequency selection, By this page, the frequency can be selected from 0.5-2.0HZ. f. By this page, the spot-size can be selected by 6mm(diameter), 8mm, 10mm, 12mm, 15mm, 18mm.you can adjust the the spot size directily on the handle. Press 5 seconds to enter into the engineer mode by password. Cold air blowing Pulse duration and Pulse interval selection. The pulse duration and pulse interval can be selected by 0ms, 50ms, 100ms, 500ms, 1000ms. If Pulse duration =1000ms, and Pulse Interval=0ms, it means the...

Press to shift wavelength from YAG to Alex. 4. “Alex” page. The alex page shows following,

The alex same as YAG. So here we do not explain again for details. 2. Treatment parameter Check the “Application” page. 3. Treatment progress Take the755nm wavelength as an example. 1064nm wavelength is the same, which will not be illustrated here again. The steps are as following: 1. Make sure the machine is installed complete; 2. Make sure the water is full filled; 3. Position the machine correctly beside the treatment table; clean the treatment area; 4. Start the machine; 5. Enter the welcome page; 6. Enter the Alex page; 7. Set up the parameters as required; 8. Press “standby” key to ready...