medical supply systems and equipment

General information on technical medical accessories The comprehensive modul technik GmbH accessories programme enables individual adaptation of medical supply units for the requirements of each workplace. Medical supply units can therefore be adapted to new local conditions either during the planning phase or retrospectively. As a result of the uncomplicated and varied structure of the modul technik GmbH accessories programme, there is a variety of possible combinations. The dimensions of the individual accessories components have proved themselves over many years and are therefore the basis...

Table of contents Page

Table of contents Expansion modules for consoles and bearer systems

Table of contents Universal modules: Separators Universal modules: Electrical engineering Halogen lamp, D

Table of contents Universal modules: Gas supply

Basic modules for IV 1054 Equipment rails (dim. 25 mm x 10 mm) as per DIN EN ISO 19054 mounted above and/or below an IV 1054, length* project specific Stainless steel equipment rail, incl. glass-fibre reinforced plastic holder and end caps, separation between holders = 400 mm: Aluminium equipment rail, incl. side cover: ▼ Accessory suitable for equipment rail: - Stainless steel carrier system for equipment rail, from side 25 - Supporting tubes for fitting to equipment rails, from side 23 * The length of the equipment rail is entered in the free spaces, e.g.: 1054-006-0800 for an equipment rail...

Basic modules Stainless steel supporting tubes Fitted on the side of an IVV 1054, length* project specific, incl. two holding devices (the separation between the holding devices is project specific) Supporting tube (diam. = 30 mm) fixed, incl. holding devices (top and bottom, inclined forwards by 45°) and end caps: Protrusion 150 mm Supporting tube (diam. = 25 mm) fixed, incl. holding devices (top and bottom, inclined forwards by 45°) and end caps: Protrusion 150 mm Supporting tube (diam. = 30 mm) swivelling, incl. holding devices (top and bottom) and end caps: □□□□ Item no.: 0446-001.02-□□□□...

Basic modules Stainless steel supporting tube Fitted on the side of an MEV 8000, length* project specific, incl. two holding devices (the separation between the holding devices is project specific) Supporting tube (diam. = 30 mm) swivelling, incl. holding devices (top and bottom) and end caps: □□□□ Item no.: 0425-001.02-□□□□ Item no.: 0425-001- (right-hand side) (left-hand side) ▼ Accessory suitable for supporting tube: - Trays for supporting tubes, from Page 27 - Cross-arms and infusion bottle holders, from Page 28 * The length of the supporting tube is entered in the free spaces of the item...

Basic modules for VIP 2000 and VIP 2001 Stainless steel supporting tubes Fitted inside a VIP 2000 or VIP 2001, incl. holding device Supporting tube (diam. = 30 mm), swivelling. Length of supporting tube approx. 400 mm Item no.: 2001-007.03 (right-hand side) Item no.: 2001-007.04 (left-hand side) ___________________________________________________________________ Supporting tube (diam. = 30 mm), swivelling, with stainless steel telescopic tube (diam. = 20 mm), max. downwards withdrawal, 400 mm: Length of supporting tube + telescopic tube approx. 800 mm Item no.: 2001-005.03 (right-hand side) Item...

Basic modules for OP 3800 Equipment rail pair (dim. 25 mm x 10 mm) as per DIN EN ISO 19054 fitted on the side facing towards the OP table (two equipment rails one above the other), Length* project-specific Aluminium equipment rails, for fitting equipment and infusion trolleys GW 3600 / IW 3600, anodized natural colour, incl. end caps: Weight / m 1.2 kg Separation, middle of rails 115 mm Aluminium equipment rails incl. curve piece, for fitting surrounding equipment and infusion trolleys GW 3600-SUF / IW 3600-SUF, anodized natural colour, incl. end caps: Weight / m 1.2 kg Separation, middle of...

Basic modules for OP 3800 Stainless steel supporting bolts for fitting a Plexiglas skirt, the arrangement of the bolts is project specific Supporting bolts:

Basic / Expansion modules Aluminium consoles (electrostatically powder coated) for fitting between two supporting tubes (diam. = 30mm, separation = 595 mm), fully vertically and horizontally adjustable, incl. two holding devices Aluminium console with four equipment rails (dim. 25 mm x 10 mm): Stainless steel console with surrounding equipment rail (dim. 25 mm x 10 mm): Aluminium console with two side equipment rails (dim. 25 mm x 10 mm): ▼ Accessory suitable for aluminium consoles: - Drawer module (Item no.: 0121-005 / Item no: 0121-005.02), Page 20 - Keyboard module (Item no.: 0106-007), Page...

Basic / Expansion modules Stainless steel consoles for fitting between two supporting tubes (diam. = 30mm, separation = 595 mm), fully vertically and horizontally adjustable, incl. two holding devices Stainless steel console with surrounding equipment rail (dim. 25 mm x 10 mm): Overall dim. (W x D) 560 mm x 510 mm Aluminium console with two side equipment rails (dim. 25 mm x 10 mm): Overall dim. (W x D) 560 mm x 450 mm ▼ Accessory suitable for stainless steel consoles: - Drawer module (Item no.: 0121-005 / Item no: 0121-005.02), Page 20 - Keyboard module (Item no.: 0106-007), Page 21 - Writing...

Basic / Expansion modules Aluminium consoles (electrostatically powder coated) for front mounting, completely vertically adjustable, incl. screw-in holders Stainless steel console with three equipment rails (dim. 25 mm x 10 mm): Aluminium console with three equipment rails (dim. 25 mm x 10 mm): ▼ Accessory suitable for aluminium console: - Drawer module (Item no.: 0121-005 / Item no: 0121-005.02), Page 20 - Keyboard module (Item no.: 0106-007), Page 21 - Writing tray (Item no.: 0261-001), Page 21

Basic / Expansion modules Aluminium consoles (electrostatically powder coated) with control element for pneumatic brakes front mounted (position project dependent), incl. screw-in holders Aluminium console with two side equipment rails (dim. 25 mm x 10 mm): Aluminium console with two side equipment rails (dim. 25 mm x 10 mm): ▼ Accessory suitable for aluminium console: - Drawer module (Item no.: 0121-005 / Item no: 0121-005.02), Page 20 - Keyboard module (Item no.: 0106-007), Page 21 - Writing tray (Item no.: 0261-001), Page 21 Aluminium console (electrostatically powder coated) with membrane...