Catalog excerpts
Dental Handpiece Maintenance Equipment Thinking ahead. Focused on life.
Open the catalog to page 1Seamless Auto-Maintenance Fast and clean operation, plus compatibility with multiple brands of spray lubricant Lubrina 2 automatically performs maintenance (lubrication and cleaning) of handpieces which are essential for daily practice. Because the lubrication amount and service time suitable for each handpiece are programmed into Lubrina 2, it can automatically perform maintenance of up to four handpieces in a short time. The clean air-blow system implements lubrication and cleaning of the inside of the handpiece thoroughly, and provides stable maintenance without variations by staff which...
Open the catalog to page 2Cleans one turbine in approximately 20 seconds Oil usage amount is reduced to 1/4 Faster maintenance with excellent cost savings Since the air-blow system can remove residual water completely using clean air, the efficiency of lubrication is enhanced with oil usage only 1/4 of that compared to manual lubrication. Daily maintenance cost is therefore reduced. In addition, the system can remove surplus oil effectively, allowing maintenance in a short time*1. Greatly shortens the maintenance process Oil usage reduced to 1/4 Manual lubrication maintenance Lubrina 2 Cleaning Chuck maintenance...
Open the catalog to page 3Clean Air-Blow System Double-conduit design achieves clean air The double-conduit design allows the clean air-blow system to achieve clean air. By employing the dual solenoid valves and clean air dedicated conduit, the system can supply clean air without a mix of oil. During the water removal process before lubrication, the system removes the water in the head which maximizes lubrication results. During idling after lubrication, the surplus oil can be effectively removed by clean air. Lubrina 2 (Clean Air-Blow System) Solenoid valve Oil Solenoid valve Conventional product* Solenoid valve *...
Open the catalog to page 4Water removal during autoclaving Easy chuck maintenance For the turbine and 5x speed contra-angle handpiece, it is essential to lubricate and clean the chuck which holds the bar. The built- in one touch chuck maintenance mechanism allows for easy maintenance. Autoclave If autoclave is performed while a large amount of water is left in the conduit of the handpiece, steam will not infiltrate and could cause a sterilization defect. To prevent this, clean air (without a mix of oil) is fed into the water feed, chip air conduit to remove the residual water, thereby reducing the possibility of a...
Open the catalog to page 5Oil spray can delivery system The low viscosity oil mist penetrates into the inside of the handpiece head and delivers intense cleaning. Morita Multi Spray (sold separately) .„T, This dedicated oil offers MULTI I, . | , excellent lubrication properties and enhances the performance of TwinPower Turbine and TorqTech. Optional Items Morita Multi Spray * The company names and product names are trademarks or registered trademarks of each company.
Open the catalog to page 6Brand name: Model: Order no.: Power voltage: Power consumption: Lubrina 2 HIM-2 2596 AC 100V-240V 50-60Hz 10-25 VA Maximum input air pressure: 0.7 MPa max. Air pressure used: 0.3-0.5 MPa (recommended 0.4 MPa) Consumed air flow rate: 60-100 NL / min (0.3-0.5 MPa) Manufactured and sold by: J. MORITA MFG. CORP. Functions Clean Air-blow System (Dual solenoid valves) Mode 1 (for turbine) Mode 2 (for contra-angle handpiece) Flushing mode Air-blow mode Chuck maintenance mechanism Spray can system Dual spray system Residual water removal mechanism Oil mist suction mechanism Compatible with...
Open the catalog to page 7Development and Manufacturing J. MORITA MFG. CORF? 680 Higashihama Minami-cho, Fushimi-ku, Kyoto 612-8533, Japan T +81. (0)75. 611 2141, F +81. (0)75. 622 4595 Morita Global Website www.morita.com Diagnostic and Imaging Equipment Treatment Units Handpieces and Instruments Endodontic System Laser Equipment Laboratory Devices Educational and Training Systems Auxiliaries Distribution J. MORITA CORF! 3-33-18 Tarumi-cho, Suita-shi, Osaka 564-8650, Japan T +81. (0)6. 6380 1521, F +81. (0)6. 6380 0585 J. MORITA USA, INC. 9 Mason, lrvine CA 92618, USA T +1. 949. 581 9600, F +1. 949. 581 8811 J....
Open the catalog to page 8All Morita catalogs and technical brochures
-
Tri Auto ZX2+
8 Pages
-
Instrument brochure
16 Pages
-
EndoWave Feilen
2 Pages
-
Signo T100
12 Pages
-
Signo Z300
12 Pages
-
Signo T500
13 Pages
-
Signo G10 II
41 Pages
-
Root ZX mini
2 Pages
-
3D Accuitomo 170
16 Pages
-
Veraviewepocs 2D
10 Pages
-
Veraview IC5 HD
5 Pages
-
GUMMETAL®
5 Pages
-
Veraviewepocs 3D R100
16 Pages
-
AdvErL EVO
6 Pages
-
TriAuto mini
10 Pages
-
Implant Dentistry
36 Pages
-
Veraview X800
10 Pages
-
TorqTech handpieces
2 Pages
-
Veraview iX
2 Pages
-
EndoWave OTR Sequence FM
2 Pages
-
Genuine Root ZX
2 Pages
-
i-Dixel Web
2 Pages
Archived catalogs
-
Soaric for endodontics
2 Pages
-
Soaric
19 Pages
-
PenCure 2000
2 Pages
-
Brochure "Endodontics is an Art"
10 Pages