Dental Handpiece Maintenance Equipment Thinking ahead. Focused on life.

Seamless Auto-Maintenance Fast and clean operation, plus compatibility with multiple brands of spray lubricant Lubrina 2 automatically performs maintenance (lubrication and cleaning) of handpieces which are essential for daily practice. Because the lubrication amount and service time suitable for each handpiece are programmed into Lubrina 2, it can automatically perform maintenance of up to four handpieces in a short time. The clean air-blow system implements lubrication and cleaning of the inside of the handpiece thoroughly, and provides stable maintenance without variations by staff which can...

Cleans one turbine in approximately 20 seconds Oil usage amount is reduced to 1/4 Faster maintenance with excellent cost savings Since the air-blow system can remove residual water completely using clean air, the efficiency of lubrication is enhanced with oil usage only 1/4 of that compared to manual lubrication. Daily maintenance cost is therefore reduced. In addition, the system can remove surplus oil effectively, allowing maintenance in a short time*1. Greatly shortens the maintenance process Oil usage reduced to 1/4 Manual lubrication maintenance Lubrina 2 Cleaning Chuck maintenance Idle...

Clean Air-Blow System Double-conduit design achieves clean air The double-conduit design allows the clean air-blow system to achieve clean air. By employing the dual solenoid valves and clean air dedicated conduit, the system can supply clean air without a mix of oil. During the water removal process before lubrication, the system removes the water in the head which maximizes lubrication results. During idling after lubrication, the surplus oil can be effectively removed by clean air. Lubrina 2 (Clean Air-Blow System) Solenoid valve Oil Solenoid valve Conventional product* Solenoid valve * Original...

Water removal during autoclaving Easy chuck maintenance For the turbine and 5x speed contra-angle handpiece, it is essential to lubricate and clean the chuck which holds the bar. The built- in one touch chuck maintenance mechanism allows for easy maintenance. Autoclave If autoclave is performed while a large amount of water is left in the conduit of the handpiece, steam will not infiltrate and could cause a sterilization defect. To prevent this, clean air (without a mix of oil) is fed into the water feed, chip air conduit to remove the residual water, thereby reducing the possibility of a problem...

-g_ Morita Multi Spray (sold separately) This dedicated oil offers jpra excellent lubrication properties and enhances the performance of TwinPower Turbine and TorqTech. Optional Items Morita Multi Spray * The company names and product names are trademarks or registered trademarks of each company.

Specifications Brand name: Power voltage: Power consumption: 10-25 VA Maximum input air pressure: 0.7 MPa max. Air pressure used: Consumed air flow rate: 60-100 NL / min (0.3-0.5 MPa) Weight: External dimensions: W300×D300×H365mm Manufactured and sold by: J. MORITA MFG. CORP. Functions Clean Air-blow System (Dual solenoid valves) Mode 2 (for contra-angle handpiece) Oil absorption sheet for front door Flushing mode Sheet stopper for door Air-blow mode Power supply cord Chuck maintenance mechanism Spray Holders (standard) x 2 Dual spray system (for Morita Multi Spray) Residual water removal mechanism...

Diagnostic and Imaging Equipment Treatment Units Handpieces and Instruments Endodontic System Laser Equipment Laboratory Devices Development and Manufacturing J. MORITA MFG. CORP. 680 Higashihama Minami-cho, Fushimi-ku, Kyoto 612-8533, Japan T +81. (0)75. 611 2141, F +81. (0)75. 622 4595 Morita Global Website www.morita.com Distribution J. MORITA CORP. 3-33-18 Tarumi-cho, Suita-shi, Osaka 564-8650, Japan T +81. (0)6. 6380 1521, F +81. (0)6. 6380 0585 J. MORITA USA, INC. 9 Mason, lrvine CA 92618, USA T +1. 949. 581 9600, F +1. 949. 581 8811 J. MORITA EUROPE GMBH Justus-von-Liebig-Strasse 27a,...