USER MANUAL Laboratory centrifuge MPW M-BASIC Read before use! Serial number of centrifuges: ………………………………………………………. For centrifuges

This manual has been prepared with particular care. At any time and without prior notice, MPW MED. INSTRUMENTS can introduce improvements and changes in the manual resulting from noticing typographical errors or improving the device. All rights reserved. No part of this document may be modified, distributed, published or reproduced without the consent of MPW MED. INSTRUMENTS. You can find the current version of the manual on our website under: https://mpw.pl/en/to-download/user-manuals Warning signs: WARNING! Warning of potential injury or health risk. DANGER! Electric shock hazard with possible...

Declaration of conformity (CE, ROHS 2) Declaration of decontamination (repair / return)

1 Application MPW M-BASIC centrifuge is a tabletop laboratory centrifuge. The device is designed especially for In Vitro diagnostics (IVD) and is used to separate samples taken from human, animal and plant organisms into components of different densities under the influence of centrifugal force, to provide information about their biological state and for other analytical works. The design of the centrifuge ensures easy operation, safe operation and a wide range of applications in laboratories for medical, biochemical and other analyzes. The centrifuge is not biotight. It is not allowed to centrifuge...

2 Technical specification Manufacturer "MPW MED. INSTRUMENTS" SPÓŁDZIELNIA PRACY, Boremlowska 46 Street, 04-347 Warsaw Type Mains voltage (L1+N+PE), Frequency Device power (max.) Current protection Capacity (max.) Running time Time counting Short-time operation mode – SHORT Continuous operation mode – HOLD User programs Acceleration (ACEL) Deceleration (DECEL) Electromagnetic compatibility Ambient conditions Set-up site Ambient temperature Humidity (max relative humidity) excess-voltage category Pollution degree Safety area Degree of protection (according to PN-IEC 34-5) Dimensions: Height (H)...

3 Installation Open the package. Remove the box containing the accessories. Take out centrifuge from the container. Save the box and packing material in case of service shipment. Connect the centrifuge to the power supply and open the cover, then remove the safety locking the rotor by following the pictures below. Content of package Name Centrifuge MPW M-BASIC Complete clamp Spanner for the rotor Spanner for emergency opening of the cover Power cord 230V or 120V Fuse for version 230V 50/60Hz Fuse for version 120V 50/60Hz vaseline 20ml Permanent marker User manual

The centrifuge should be lifted and transported with a sufficient number of helpers. Use a transport aid to transport the centrifuge. The device should be lifted by its bottom and placed directly on a suitable laboratory table. The centrifuge should be set so that access to the power switch is not difficult. A safe installation site must be provided. Do not place the centrifuge near heaters and avoid direct sunlight. The table on which the centrifuge is placed should be stable and have a flat, leveled top. Leave a distance of 30 cm around the centrifuge to maintain the ventilation zone. Do not...

4 Safeness Operating personnel ▪ The laboratory centrifuge may be operated only by qualified laboratory personnel after getting acquainted with the operating manual. The manual is an integral part of the device. The manual should always be kept near the centrifuge. The centrifuge cannot be operated improperly or inconsistently intended. If the centrifuge is used in a manner inconsistent with the manufacturer's guidelines, the safety of the device operation may be impai

Safety hints Rotors maintenance ▪ Lubricate the rotor pins with technical petroleum jelly (supplied with the rotor) Use only accessories in good technical condition. Use accurate preventive maintenance to prevent corrosion of the equipment (see chapter Maintenance). It is not allowed to centrifuge toxic or infectious materials with damaged hermetic seal of the test tube. Proper disinfection procedures should always be performed, if dangerous substances have contaminated the centrifuge or its accessories. Explosive, flammable materials ▪ It is not allowed to centrifuge explosive and inflammable...

It is not allowed to start the centrifuge if it is not installed correctly or the rotor and accessories are not properly mounted. It is not allowed to exceed load limit set by the manufacturer. Rotors are intended for fluids of average homogeneous density equal to 1,2 g/cm3 or smaller. Inspection procedures carried out by the operator Operator must pay special attention to the fact that the centrifuge parts of key importance due to safety reasons are not damaged. This remark is specifically important as for: ▪ Centrifuge accessories and especially structural changes, corrosion, preliminary cracks,...

It is not allowed to use containers and round carriers with signs of corrosion or other mechanical damage. It is not allowed to centrifuge substances of high corrosive aggressiveness, which may damage materials and reduce mechanical properties of the rotor, buckets and round carriers. Residual risk The centrifuge is built according to the state-of-the-art and the recognized safety regulations. Nevertheless, remain some level of residual risk due to improper operation and malfunctions. It is possible to decrease residual risk by strictly applying user manual conditions and correcting malfunction...

5 Operating Centrifuge description The MPW M-BASIC laboratory centrifuge is equipped with a modern microprocessor controller, a durable and quiet brushless induction motor and equipment that meets modern user requirements. The housing and cover are made of ABS plastic, the base is made of aluminum sheet. The cover is mounted on steel hinge axes, and from the front it is secured against opening it during rotation with an electromagnetic lock. The spin chamber is made of stainless steel. Control panel Lid Inspection glass Point of emergency lid opening Name plate Mains switch Control panel The...