USER MANUAL MPW M-UNIVERSAL Laboratory centrifuge MPW M-DIAGNOSTIC Laboratory centrifuge MPW M-SCIENCE Laboratory centrifuge Serial number of the centrifuge: ………………………………………………………. For centrifuges with serial no (SN): MPW M-UNIVERSAL: from 102MU013219 MPW M-DIAGNOSTIC: from 102M

This manual was prepared with special care. MPW MED. INSTRUMENTS may change the manual at any time and without notice because of improvements, typographical errors or improvements to facilities All rights reserved. No part of this User Manual may be modified, distributed, published or reproduced without the prior permission of MPW MED. INSTRUMENTS. You can find the current version of the user manual on our website under: www.mpw.pl DOWNLOAD section (one should choose demanded language version of website). Warning signs: WARNING! Warning of potential injury or health risk. DANGER! Risk of electric...

ADDITIONAL ACCESSORIES DECLARATION OF CONFORMITY ROHS 2 D. DECLARATION OF DECONTAMINATION (repair / return) E.

1 Application MPW M-DIAGNOSTIC/MPW M-SCIENCE/MPW M-UNIVERSAL centrifuges are table top laboratory centrifuges for in vitro diagnostic (IVD). Devices are used for separation samples taken from people's, animal’s and plant’s components of different densities, under the influence of the centrifugal force, to provide information about their biological state. Its construction ensures easy operation, safe work and wide range of applications at laboratories engaged in routine medical analyses, biochemical research works etc. This centrifuge is not bio tight and therefore during centrifugation of preparations...

3 Installation Open the package. Remove the box containing the accessories. Take out centrifuge from the container. Keep the box and packing materials in case of service shipping. Content of the package name centrifuge MPW M-UNIVERSAL/MPW M-DIAGNOSTIC / MPW M-SCIENCE / complete clamp spanner for the rotor spanner for emergency opening of the cover power cord 230V / 120V fuse WTA T8A 1150V vaseline 20ml USB A-A cable user manual The device is heavy, so lifting and carrying the centrifuge can lead to back injuries. Risk of injury while lifting and carrying heavy loads. Lifting and transporting...

Before switching on, check whether the centrifuge is connected to power supply correctly. It is obligatory to use only power cord reccomended by manufacturer (17866 for 230V, 17867 for 120V). Current protection The centrifuge is equipped with thermal current protection. Fuse is situated in the plugin socket unit at back wall of the centrifuge. 4 Operating safety Operating personnel ▪ ▪ ▪ ▪ ▪ Laboratory centrifuge can be operated by laboratory personnel after getting acquainted with user manual. This User Manual is part of the device. User manual shall be always held near the centrifuge. The centrifuge...

It is necessary to insert test tubes symmetrically on the opposite sides. Fill test tubes outside the centrifuge. Please pay special attention to the quality and proper thickness of the glass test tubes walls. Those shall be test tubes for centrifuges. Fill test tubes outside the centrifuge. Safety hints ROTORS MAINTENANCE ▪ ▪ ▪ Lubricate the swing-out rotor journal pins. Use only accessories in good condition. Protect equipment against corrosion using accurate preventive maintenance. Make sure that rubber O-rings are lightly coated with silicone grease. Use high vacuum grease, e.g. type „C”...

Maintenance conditions START-UP ▪ Prior to switching the centrifuge on, one shall read carefully all sections of this instruction in order to ensure smooth operation and avoid damages of this device or its accessories. In order to protect the centrifuge against unbalance, fill in the test tubes up to the same weight. Centrifuge must not be transported with the rotor mounted on the shaft.. One must use original rotors, test-tubes and spare parts only. In case of faulty operation of the centrifuge one shall ask for assistance of service of MPW MED. INSTRUMENTS company or its authorized representatives....

It is not allowed to use the rotors and round carriers with signs of corrosion or other mechanical defects. It is not allowed to centrifuge highly corrosive substances which may cause material impairment and lower mechanical properties of rotor and round carriers. It isn’t allowed to use rotors and accessories not admitted by the manufacturer. Let to use commercial glass and plastic test tubes, which are destined to centrifuging in this laboratory centrifuge. One should absolutely not use poor quality elements. Cracking of glass vessels and test tubes could result in dangerous vibration of the...

Rys.4. Back of the centrifuge I. Main socket II. Fuse socket III. USB [M-UNIVERSAL only] 1. Motor axle 2. Rotor 3. Rotor lid 4. Complete clamp Rys.3. Assembly of angle rotor The centrifuge has rigid self-supporting structure. Front and lid was made of ABS type plastic. Lid is fixed on steel axles of hinges and from the front it is locked with two electromagnetic locks blocking possible opening during centrifugation. Rotation chamber casing was made of thick steel sheet. The rotation chamber bowl is made of stainless steel sheet. Name plate Centrifuge model Catalogue number Power supply parameters...

Rotor and accessories installation ▪ ▪ ▪ Connect the centrifuge to the mains (master switch on the back side of the centrifuge). Turn on the centrifuge (button on the side of the centrifuge). Open the cover of the centrifuge by pressing the COVER key (see section Centrifuging/Control Panel). Prior to putting the rotor in, one has to check if the rotating chamber is free of impurities, e.g. such as dust, glass splinters, residues of fluids that must be taken away. One shall fit the rotor on the motor shaft driving it home on the cone. Screw-in the bolt for fixing the rotor (clockwise) and screw...