ALIANS ULNA
8Pages

{{requestButtons}}

Catalog excerpts

ALIANS ULNA - 1

ALIANS ULNA CUTTING AND COMPRESSION DEVICE MONOAXIAL LOCKING SYSTEM Ulnar shortening osteotomy plate Rack-and-pinion compression device Ø2.8 mm interfragmentary cortical screw

Open the catalog to page 1
ALIANS ULNA - 2

Indications: The ALIANS ULNA locking plating system is intended for ulnar shortening osteotomy in adults. Contra-indications: • Pregnancy. • Acute or chronic local or systemic infections. • Lack of musculo-cutaneous cover, severe vascular deficiency touching the focus. • Insufficient bone quality preventing the correct insertion of the screws into the bone. • Muscular deficit, neurological deficiency or behavioural disorders, which could submit the implant to abnormal mechanical strains. • Allergy to one of the materials used or sensitivity to foreign bodies • Serious problems of...

Open the catalog to page 2
ALIANS ULNA - 3

CUTTING AND COMPRESSION DEVICE COMPONENTS The block should be chosen according to: 2 blocks (ANC171 and ANC172) depending on the side of the resection (right or left) and the approach (lateral, dorsal or palmar/volar) Each block includes: - A written indication of the corresponding side / approach: depending on the chosen side, these indications help to determine the appropriate block and to assemble the cutting and compression device. - A rack-and-pinion system allowing for optimal compression of the osteotomy sites. • The side: right or left • The selected approach: lateral, dorsal or...

Open the catalog to page 3
ALIANS ULNA - 4

STEP 1 Position the plate on the most distal part of the ulna making sure that the ‘distal-proximal’ marks are correctly matched. The approach used and positoning of the plate may be lateral, dorsal or palmar (volar). STEP 2 In the most distal hole, drill (ANC089C) and directly read the drilling depth on the guide gauge (ANC186). STEP 3 To ease the insertion of the 03.5 mm locking screw (SOT3.5Lxx), use : - the hand reamer (ANC463) (3.a) or - the reamer part of the 2-in-1 instrument (ANC083C) (3.b), to widen the first cortex previously drilled. Remark: perform reaming for the insertion of...

Open the catalog to page 4
ALIANS ULNA - 5

8.a 9. IQ. STEP 7 Screw the drill guide (ANC192) into the proximal part of the block and perform bicortical drilling (ANC089C) to enable the subsequent insertion of the handle for compression. STEP 8. a Perform the two cuts necessary for the ulnar shortening osteotomy using the cutting guide at graduation 0 at first. STEP 8. b Then at the graduation corresponding to the required resection. The resection is thus made by two oblique saw cuts. STEP 9 Remove the cutting guide to pull out the resected bone fragment. STEP 10 Slightly loosen the two cortical screws (CT3.5Lxx) in the oblong hole so...

Open the catalog to page 5
ALIANS ULNA - 6

To maintain the stability, insert the Ø2.8 mm cortical screw (CT2.8Lxx) in the pre-angled hole. For this purpose, position the guide gauge (ANC450) on the pre-angled hole (50°), perform the drilling and directly read the drilling depth on the guide gauge. Insert the Ø2.8 mm cortical screw (CT2.8Lxx) using the appropriate screwdriver (ANC082). FINAL RESULT Complete the procedure by inserting the last two Ø3.5 mm locking screws (SOT3.5Lxx) into the proximal part of the plate. Do not forget to use the reamer (ANC463) or the reamer part of 2-in-1 instrument (ANC083C) after the dril

Open the catalog to page 6
ALIANS ULNA - 7

ALIANS ULNA PLATE Ref. Description HTSIS1 Symmetrical osteotomy plate for Ulna - Size 1 LOCKING SCREWS* QOT3.5L10 03.5 mm non locking screw - L10 mm QOT3.5L12 03.5 mm non locking screw - L12 mm QOT3.5L14 03.5 mm non locking screw - L14 mm QOT3.5L16 03.5 mm non locking screw - L16 mm QOT3.5L18 03.5 mm non locking screw - L18 mm QOT3.5L20 03.5 mm non locking screw - L20 mm Pink anodized Blue anodized CORTICAL SCREWS * CORTICAL SCREWS

Open the catalog to page 7
ALIANS ULNA - 8

Non-contractual pictures. Qty ANC082 2.0 mm quick coupling hexagonal prehensor screwdriver 1 ANC083C 2-in-1 : 2.5 mm hexagonal prehensor screwdriver - 03.5 mm reamer 1 ANC107 02.5 mm quick coupling hexagonal non-prehensor screwdriver 1 ANC124 Length gauge for 03.5 mm cortical screws 1 ANC170 02.7 mm handle for Ulna cutting and compression device 1 ANC171 Left block for Ulna plate 1 ANC172 Right block for Ulna plate 1 ANC319 02.7 mm double guide gauge for 03.5 mm cortical screws - Ulna 1 ANC350 04.5 mm AO quick coupling...

Open the catalog to page 8

All Newclip Technics catalogs and technical brochures

  1. INITIAL C™

    12 Pages

  2. PERIACTIV

    3 Pages

  3. Single Use kit

    12 Pages

  4. NATIV

    2 Pages

  5. ATLANTIC OW

    6 Pages

  6. ATLANTIC CW

    6 Pages

  7. FLATFOOT

    2 Pages

  8. Activ Ankle

    8 Pages

  9. FOREFOOT

    8 Pages

  10. ACTIVMOTION

    8 Pages

  11. INITIAL R

    8 Pages

  12. KEMIS

    4 Pages

  13. ALIANS ELBOW

    8 Pages