Group: IMI Precision Engineering
Catalog excerpts
FAS 10 mm PICOSOL MS Media separated solenoid valve > 3/2 UNI Media separated Manifold mounting > Excellent flow to size ratio > Low internal volume, excellent cleaning ability > Low energy consumption 3,5/0,4 W > Patented double rocker mechanism Technical features Medium: Neutral or aggressive gases and liquids Operation: Direct acting 3-way universal media separated valve Operating pressure: -0,95 ... 2,2 bar (-13,7 ... 32 psi) Flow: kv: 0,65 l/min [16 l/min at Ap = 1 bar (14,5 psi)] Mounting: Manifold Orifice: 1,2 mm Life expectancy: > 10 Mio. cycles Weight: 15 g (0.03 lbs) Ambient/media temperature: 10 ... +50 °C (+50 ... +122°F) Air supply must be dry enough to avoid ice formation at temperatures below +2 °C (+35°F). Materials: Body in contact with media: PEEK Seal and diaphragm material in contact with media: FFPM, EPDM Electrical details Voltage tolerance: ± 10 % Voltage: 24 V d.c./>60 ms Electrical insulation: 500 V a.c.Protection class: IP 51 Insulation class: F (155 °C) Integrated pulse width modulation (PWM) Larger input voltage tolerances Improved boosting by plunger detection Reverse polarity protection Following options on request Orifice size Operating pressure Medium temperature Ambient temperature Response time Power consumption Materials Coils Manual override Embedded electronics options Technical data - standard models El Operating pressure Maximum back kv *2) pressure *1) (bar) (psi) (bar) (psi) (l/min) Seal/ Drawing Model diaphragm Material No. *1) Maximum back pressure during commutation: 50% of operating pressure *2) Cv = 0,07 kv *3) Power consumption: ^boosting power during approx 50 ms“/ „holding power“ Accessories Electrical connection 1IV yi I Precision 11 w 11 Engineering Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. (2015 - 5018c) © 2015 Fluid Automation Systems s.a.
Open the catalog to page 1FAS 10 mm PICOSOL MS Media separated solenoid valve Dimensions shown in mm Projection/First angle Sealing area The recommended mounting screw tightening torque is 0,15 + 0,1 Nm. All solenoids are supplied with mounting screws and gasket. Manifold Model: On request (PEEK) Electrical connector Model: S110.1032 Threads for mounting screws - M2 x 5 mm deep Warning These products are intended for use in neutral or aggressive gases and liquids only. Do not use these products where pressures and temperatures can exceed those listed under »Technical features«. Before using these products with...
Open the catalog to page 2All Norgren FAS MEDIC SA catalogs and technical brochures
-
Acro 600 Series
2 Pages
-
6 cm Rotary Valves
3 Pages
-
3cm Rotary Valves
3 Pages
-
Acro PN200 Series
16 Pages
-
ACRO PINCH VALVES
8 Pages
-
Cadent 3 Syringe Pump
5 Pages
-
CHIPPROP
2 Pages
-
Multi stage vacuum pumps
3 Pages
-
Single stage vacuum pumps
2 Pages
-
EXPRESS CATALOGUE
228 Pages
-
FAS 16 mm FASPROP
4 Pages
-
FAS 32 mm BACOSOL
4 Pages
-
Multi-Channel Syringe Pump
4 Pages
-
V6 Syringe Pump
4 Pages
-
ISO Roundline Cylinders
11 Pages
-
ISO/VDMA cylinders
23 Pages
-
IMI FAS CHIPSOL
4 Pages
-
IMI FAS FLEXISOL
4 Pages
-
CHIPSOL MS
3 Pages
-
Cadent Pump Brochure
6 Pages
-
V6 Syringe Drive Pump
4 Pages