Blood Glucose Meter 4117A
1 / 42Pages

Blood Glucose Meter Owner’s Manual

Thank you for purchasing the Blood Glucose Meter. This manual provides important information to help you to use the system properly. Before using this product, please read the following contents thoroughly and carefully. Regular monitoring of your blood glucose levels can help you and your doctor gain better control of your diabetes. Due to its compact size and easy operation, you can use the Blood Glucose Meter to easily monitor your blood glucose levels by yourself anywhere, any time. If you have other questions regarding this product, please contact the place of purchase or call...

IMPORTANT SAFTY INSTRUCTIONS READ BEFORE USE 1. Use this device ONLY for the intended use described in this manual. 2. Do NOT use accessories which are not specified by the manufacturer. 3. Do NOT use the device if it is not working properly or if it is damaged. 4. Do NOT use the equipment in places where aerosol sprays are being used or where oxygen is being administered. 5. Do NOT under any circumstances use the device on newborns or infants. 6. This device does NOT serve as a cure for any symptoms or diseases. The data measured is for reference only. 7. Before using this device to test...

Important Information Intended Use Test Principle Meter Overview Display Screen Test Strip Setting the Meter THE FOUR MEASURING MODES TESTING WITH BLOOD SAMPLE 14 15 Control Solution Testing Performing a Control Solution Test TESTING WITH BLOOD SAMPLE 18 Preparing the Puncture Site Alternative Site Testing Performing a Blood Glucose Test Reviewing test results Reviewing Blood Glucose Day Average Results Downloading Results Onto A Computer Battery Caring for Your Meter Caring for Your Test Strips Important Control Solution Information Result Readings Error Messages Troubleshooting DETAILED...

• Severe dehydration and excessive water loss may cause readings which are lower than actual values. If you believe you are suffering from severe dehydration, consult a healthcare professional immediately. • If your blood glucose results are lower or higher than usual, and you do not have any symptoms of illness, first repeat the test. If you have symptoms or continue to get results which are higher or lower than usual, follow the treatment advice of your healthcare professional. • Use only fresh whole blood samples to test your blood glucose. Using other substances will lead to incorrect...

Intended Use This system is intended for use outside the body (in vitro diagnostic use) by people with diabetes at home and by health care professionals in clinical settings as an aid to monitoring the effectiveness of diabetes control. It is intended to be used for the quantitative measurement of glucose (sugar) in fresh whole blood samples (from the finger, palm, forearm and upper arm). Professionals may test with capillary and venous blood sample; home use is limited to capillary whole blood testing. It should not be used for the diagnosis of diabetes, or testing on newborns....

1 Display Screen 2 Test Strip Ejector Eject the used strip by pushing this button up. 3 Test Slot Insert test strip here to turn the meter on for testing. 4 SET Button Enter and confirm the meter settings. 5 Data Port Download test results with a cable connection. 6 Main Button Enter the meter memory and silence a reminder alarm.

Display Screen i Low battery symbol 2 Test strip symbol 3 Blood drop symbol 4 Test result 5 Ketone warning 6 Error Message 7 Memory symbol 8 Control solution mode 9 Measuring mode 10 Date 11 Time 12 Day average 13 Reminder alarm 14 Face/Low/High symbol 15 Measurement unit

Test Strip Absorbent Hole Apply a drop of blood here. The blood will be automatically absorbed. Test Strip Handle Hold this part to insert the test strip into the slot. Confirmation Window This is where you confirm if enough blood has been applied to the absorbent hole in the strip. Contact Bars Insert this end of the test strip into the meter. Push it in firmly until it will go no further. ATTENTION: The front side of test strip should face up when inserting test strip. Test results might be wrong if the contact bar is not fully inserted into the test slot. Front NOTE: The monitor should...

Before using your meter for the first time or if you change the meter battery, you should check and update these settings. Make sure you complete the steps below and have your desired settings saved. Entering the Setting Mode Start with the meter off (no test strip inserted). Press SET. 1. Setting the date With the year flashing, press M button until the correct year appears. Press SET. ID-D5 MO* ID-OS MD" With the month flashing, press M button until the correct month appears. Press SET. With the day flashing, press M button until the correct day appears. Press SET. 2. Setting the time...

3. Setting the time With the hour flashing, press M button until the correct hour appears. Press SET. With the minute flashing, press M button until the correct minute appears. Press SET. 4. Deleting the memory With “dEL” and a flashing “ [m] ” symbol on the display, press M button and select “No” to keep the results in memory then press SET to skip. To delete all the results, press M button and select YES to delete all the memory records. 5. Setting the reminder alarm You may set up any or all of the reminder alarms (1-4). The meter displays “On” or “OFF” and ” ”, press M to turn on or...

If you do not want to set an alarm, press SET to skip this step. If you want to turn off an alarm, find the alarm number by pressing SET in the setting mode, press M button to change from ON to OFF . At the time of your alarm, the meter will beep and automatically turn on. You can press M button to silence the alarm and insert a test strip to begin testing. If you do not press M button, the meter will beep for 2 minutes then switch off. If you do not want to test at this time, press M button to switch off the meter. Congratulations! You have completed all settings! NOTE: • These parameters...