(Jibeca Arm Automatic Blood Pressure Monitor Instruction Manual Model: BA2318

1. Safety Information 1.1 Warning A • Self diagnosis and treatment which use measured results may be dangerous. Follow the instructions of your physicia or licensed healthcare provider. If cuff inflation doesn’t stop, remove the cuff or power off the unit , otherwise, it may result in a hazard condition. • Only take measurement with the manufacturer supplied cuff or else it will lead to inaccurate results. • Do not use the blood pressure monitor when you are close proximity to strong static electricity or electromagnetic fields and avoid using the mobile during measurement. Do not use in combination...

The battery has positive/negative polarity. If the battery does not connect well to the unit, do not forcibly connect it. Do not use Luer lock. If Luer lock connectors are used in the construction of tubing, there is a possibility that they might be inadvertently connected to intravascular fluid systems, allowing air to be pumped into a blood vessel. This product is suitable for use to self- monitoring of blood pressure in home or used by the licensed healthcare per sonnel in hospital. Blood pressure measurements determined with the device are equivalent to those obtained by a trained observer...

Rev:A1 Do not measurement too frequent, or else it may result in bruising where the cuff is applied. • Do not apply the cuff over a wound or inflamed area. The application of the cuff and its pressurization on the arm can cause temporary interference to blood flow, but it would not result in injury to the patient. Operation of the device does not result in prolonged impairment of the circulation of the blood of the patient. Direct plug is considered as disconnect device, please do not place the equipment in a difficultly operation position. When using the device, the patient is an intended operator. Do...

Avoid high temperature, moisture, dust and direct sunlight. Clean the body with soft dry cloth dipped in a concentration of 75% medical alcohol. Do not wet or cleaning the cuff with water. Clean the cuff with soft dry cloth after measurement. Do not use at extremely high temperature, high humidity, or high altitude. Use only within the required ambient conditions. Do not drop or expose the device to heavy shock. Do not use the unit near large equipment that uses a switching relay for power ON/OFF. Remove the batteries if the unit will not use for a long time. The blood pressure monitor has gone...

Body SET ON/OFF Memory Fig 1 Cuff (Type BF Applied Part) Model：BC1000 Applicable Arm Circumference: 220 mm to 360 mm Air Tube Connector Cuff

Fig 2 Symbol for TYPE BF APPLIED PART Display Blood Pressure Level Indicator Heart Mark Irregular Heat Rate Symbol Battery Symbol --Memory1 — Memory2 *&fSB8*BB Mean Symbol Date and Time Pulse Rate —Average Symbol

3. Pre Measurement 3.1 Battery 3.1.1 Installation and replacement 1）Remove battery cover 2）Load 4 standard AAA alkaline battery as indicated in figure below 4 x AAA Please use the same brand battery and aware of battery polarity during installation Fig 4 3）Install back the battery cover 4）Replace the battery if low battery icon is displayed If the low battery symbol is display, replace with new batteries, otherwise the unit will not function properly. Use 4 same brand 1.5 Volt AAA alkaline batteries. Do not mix the new and old batteries. Remove the battery if the unit is to remain unused for...

Rev:A1 The batteries enclosed in the package are used for demonstration purpose. It is possible that these batteries will therefore not last for 200 measurements. The battery life can be confirmed in the bottom left of the display. If the low battery symbol m - is display, remaining power is low, replace with new batteries. 3.2 Setting 3.2.1 Setting 1) With monitor power off 2) Hold the [Set] button for 3 seconds, Year digits blinking a) Change number i Press the [ M ] button to advance one number ii Hold down the [ M ] button the number will change rapidly b) Enter the two digit of the year...

b) Complete setting, press 【ON/OFF】 button to exit. 3.2.2 Memory Data Conversion The blood pressure monitor is capable to hold 2 sets of memory data. Prior using the blood pressure monitor, select the correct memory data. Memory data conversion: With monitor power off, hold the【ON/OFF】button until the selected Memory displayed. Press the【ON/OFF】button will automatically change the memory data conversion either from Memory 1 or Memory 2. The machine is complete setting, ready

4 Take a measurement 4.1 Important Noted Don't eat, drink alcohol, smoke, take a shower or exercise for at least 30 minutes before you take your blood pressure and don't use any medicines that can raise blood pressure. Try not to take your blood pressure if you are nervous or upset. If we are nervous, anxious, or agitated our blood pressure will rise. Rest for 5～10 minutes before taking a reading. Sit in a comfortable, relaxed position. Don't move around or talk while taking the blood pressure. Leave your legs in one position, breath freely and calmly. The blood pressure cuff should fit over...

Rev：A1 Air tube bladder locates in the center of the arm. Fig 9 4 ) Make sure cuff air tube outlet is facing your finger. Do not over tighten. Approximate one finger should be able to fit underneath the cuff after tightening. 5 ) Relax, place the elbow on the desk with palm facing up; the cuff should be level with your heart. If the cuff doesn’t fit your arm, the reading accuracy may be affected. Do not bend with the cuff or the air tube. To detach the cuff, unplug the air tube connector from the main unit Do not inflate prior fitting the cuff. Change the cuff, if it there is a leakage or if...

Rev：A1 Arm should be at the same level of your heart. 4.4 Take Measurement After installing the batteries and wearing the cuff, the unit is ready for measurement: 1 ) For the most accurate result please relax, do not smoke, take deep breath, speak loudly or move around during the measurement. 2 ) Turn on the 【ON/OFF】 button; display will lit-up for 1 second as shown on Fig 11. 3 ) Then the display on switch to Fig 12, a beep sound indicates the monitor has begun taking the measurement. 4 ) When the device detects a pulse, the heart symbol will flash as shown on Fig 13. The cuff inflates, and...