Rifton Stander Size 2 & 3 Thank you for choosing the Rifton Stander system. This quick reference guide will help you with basic adjustments. For more details and important safety information and warnings, please consult the product manual. Quick Reference Guide Rifton PO Box 260 Rifton NY 12471 www.rifton.com The Rifton stander system can be configured for prone or supine use. Review the available components to determine which your stander can be used for. Additional components can be obtained from www.rifton.com. Straps have color coded tags. Use components with GREEN tags for supine positioning, and components with BLUE tags for prone positioning. To avoid falls or strangulation, always ensure the correct straps and supports are used in each configuration. The infographic to the left shows the minimum straps and supports required for safe positioning in prone and supine standing. These minimum supports are denoted throughout this guide by * for supine and * for prone. Height Adjustment Product can tip over if used incorrectly. Always engage brakes during transfers and standing. Use the hand crank to adjust stander height. Frame Adjustments Body support tilt To prevent falls or other injury, ensure all straps are secure and knobs tight before tilting client to a standing position. Frame Adjustments Grasp the handle firmly and squeeze the double trigger to adjust the body support angle. Body Support Adjustment *Upper trunk support SUPINE ONLY Adjust the upper trunk support height by squeezing the two white triggers together and moving it to the desired location. The headrest is attached to the upper trunk support. Adjust the headrest forward and back using the center knob (A). Optional head laterals slide into the slots behind the headrest. Loosen the knob to adjust independently in height and width. Body Support Adjustment Headrest SUPINE ONLY A Hip depth adjustment Hip Adjustment Adjust the hip depth, moving the whole leg support forward or back relative to the body support by turning the top knob (B) behind the hip support pad. Read the position on the indicator (C). B Loosen knob (A) behind the user’s hip to adjust abduction angle, and tighten in the desired position. Thigh length TIP: Align the user’s hips at the labeled marking. Align the center of the user’s knee with the knee strap attachment posts (C). Thigh Length Loosen the knob (B) behind the center of the thigh pad and adjust the length of the hip to knee segment. It is easier to move this by pushing up or down lower on the leg support, near the sandal. Lower leg length Lower Leg Length Loosen the knob (A) behind the lower leg pad and adjust the length of the knee to foot segment. Knee Flexion Adjust the knee flexion angle using the knob (D) behind the knee. Adjust hip flexion using the knob (B) toward the outside of the hip. To adjust the leg support below the plane of the body support, pull the red trigger (C). Ankle plantar flexion/dorsiflexion Ankle / Sandals Use the knob on the inner side of the sandal to adjust ankle plantar flexion/dorsiflexion. **Sandals Loosen the knob under the sandal to rotate the sandal or move it forward or backward. The front and rear foot straps have magnetic buckles. Adjust the length of the heel cup using the velcro strap. Tray Loosen the knob that faces forward to adjust tray height. Loosen the two oval knobs to rotate and position the tray. The wing knob closest to the body support is the tray attachment and can allow slight sideways movement. The knob under the center of the tray also allows some angle adjustment. Tray Height 2 oval knobs Wing knob Tray Adjustments Tray adjustm

Medial/Lateral thigh supports Thigh Medial / Laterals Mount the medial/lateral thigh supports on the inside for medial support, or on the outside for lateral support. Adjust the width using the white trigger (A). The mounting bracket is off-center, so the pad has two possible height positions. Swap pads to change height position. A Trunk laterals Trunk Laterals Attach the laterals at the level of either the trunk or pelvis. Adjust width using trigger (B) on the side of body support. Adjust height by loosening the knob (C) on the outside and moving the pad up or down. The pads swing away for transfers...