Medical bath trolley - Neptun
1 / 12Pages

User manual Medical bath trolley - Neptun - Model 130-00108-00

Medical bath trolley Neptun

Medical bath trolley Neptun 1. Introduction – bath trolley Neptun Thank you for choosing Rini's bath trolley Neptun for neonatal care. The bathing trolley is developed to offer the best possible comfort, ergonomics, strength, and practical design to meet the demands of daily work. Both patient and operator have been in focus in connection with the development The bath trolley has battery-powered height adjustment, and the height range is large, approx. 500mm, to allow for an optimal ergonomic working position. The tub is made of plastic with a durable surface, the frame is made of stainless...

Medical bath trolley Neptun 4. Product classification and key data The product is designed for use in hospitals, specialist clinics or similar care environments by professional staff. The product's risk class in accordance with MDR 2017/745 Annex VIII is “Class 1”. Previous generations and similar products are also within risk class “Class 1”. The product's device class according to the US FDA is “Class 1” and exempt from premarket notification 510(k) requirements. The product is traceable via serial number and Rini has a "Post-market surveillance" system integrated within its quality...

Medical bath trolley Neptun 1. Four lockable wheels 2. Control box with battery 3. Lifting column 4. Bathtub 5. Handles & towel rails 6. Hand control 7. Outlet with tap 5.1 Areas of use The bath trolley Neptun has been developed to facilitate the daily work of staff in neonatal care. The trolley is raised and lowered using an electrically controlled telescopic column where positions from lowest to highest height allow a good ergonomic working position for the operator. Height adjustment takes place via corded hand control, which is advantageously hung on the driving handle to be easily...

Medical bath trolley Neptun The product has four easy-rolling wheels, which are lockable. The wheels are braked by pressing down on the wheel's locking lever with your foot. The brake is released by pulling up the wheel lock lever. It is important that the wheels of the bath trolley are kept locked when in use. Improper use can cause personal injury. The bathing trolley must not be used for passenger transport. 5.3 Height adjustment The lifting device is a battery-powered motor, which consists of motor, control unit and battery. The height is regulated using a hand control. Hight adjustment...

Medical bath trolley Neptun Batteries have a limited lifespan and must be replaced after approximately four years of use under normal operating conditions. For optimal performance, the battery should be charged weekly and at least every three months to avoid damage caused by self-discharge. 6. Cleaning, disinfection and service Only the bathtub counts as surfaces close to the patient. General cleaning should be done as needed and exposed parts should be cleaned after each use. It is important to follow the hospital/clinic's cleaning regulations and routines. Part Bathtub chassis and wheels...

Medical bath trolley Neptun 6.2 Dismantling and installation of outlets Hold the hose and slightly loosen the black knob. Then release the hose clamp with a screwdriver to release the hose. Hold against the outlet when the hose is detached. Remove the locking knob and the black rubber gasket. Then lift out the outlet and loosen the plug and check the o-ring. Installation of drains with new parts is done in reverse order.

Medical bath trolley Neptun 6.3 Replacing the battery modules The batteries are in the control unit which is mounted on the underside of the bathing trolley. To replace batteries: 1. Unplug the cable connectors 2. Carefully place the cart on its side 3. Unscrew 4 screws holding the box Be careful when turning the cart, the cart is heavy and can cause personal injury. Avoid bumping the cart. This may cause material damage. Use a small screwdriver to open the cover of the control box. Remove the batteries and unplug the connectors. Insert new batteries and reconnect them accordingly....

Medical bath trolley Neptun 7.1 CE Deklaration Bath trolley 130-00108-00 follows EU Medical Device Regulation 2017/745 for medical products. Tested according to IEC 60601-1 8. Technical specification General Weight Bathtub L X W Medical classification Standard Protective class Battery Charger Operator data Lifting capacity Height adjustment 20kg 850 - 1220mm – with push button Operational environment Temperature Relative humidity Atmospheric pressure Transport and storage Temperature Relative humidity Atmospheric pressure 8.1 Disposal and recycling The product is mainly made from...

Medical bath trolley Neptun

Rini Ergoteknik AB Fågelsångsvägen 3B SE-186 42 Vallentuna Sweden Phone +46 8 594 77170 Email info@rini.se www.rinicompany.com www.rini.se