Incubator T20
12Pages

{{requestButtons}}

Catalog excerpts

Incubator T20 - 1

Operating Instructions Incubator T20 Documentation Version 7.2017 ROBERT RIELE GmbH & Co KG

Open the catalog to page 1
Incubator T20 - 2

ROBERT RIELE GmbH & Co KG

Open the catalog to page 2
Incubator T20 - 3

SYMBOLS The packaging material, the type plate on the instrument, and the manual may contain the following symbols or abbreviations: Manufactured by: This product is marked with the CE certification mark which is obligatory in European Economic Area. Caution (refer to accompanying documents)! Please refer to safety-related notes in the manual accompanying this device. Please consult instructions for use Biohazard Samples containing material of human origin must be treated as potentially infectious. The relevant laboratory guidelines on safe use must be observed. No special protection...

Open the catalog to page 3
Incubator T20 - 4

SAFETY INSTRUCTION This device was examined and left the factory in perfect technical condition. To preserve this and protect safe and faultless operation, the user has to follow the orders and remarks of this operating manual. PROTECTIVE GRADE The Incubator T20 complies with the safety rules according to DIN EN 61010-1. The device fulfils the EMC immunity requirements for laboratory use equipment according to the EMC standard EN 61326. WASTE MANAGEMENT NOTE At the end of the life or utilization time the device and the accessories can be given back with costs to the manufacturer to an...

Open the catalog to page 4
Incubator T20 - 5

QUALITY MANAGEMENT SYSTEM ROBERT RIELE GmbH & Co KG maintains a quality management system according to ISO 13485, certified by mdc medical device certification GmbH. INTRODUCTION TO INCUBATOR T20 To make laboratory work more efficient carrying out kinetic tests it is necessary to pre-incubate samples before measuring. Beside this also the reagents must be held at the incubation-temperature during a series of measuring. For this purpose, a small and handy dry-incubator was designed as either a stand-alone system with external power supply or in direct connection to RIELE Photometers 4040,...

Open the catalog to page 5
Incubator T20 - 6

Delivery After carefully unpacking the device, check whether it is in perfect condition. Check whether it is complete according to the delivery note. The box contains the following items:  Incubator T20  AC-Adapter, optional  Manual Store the packaging carefully for the case of a perhaps necessary return. If there were defects, inform your dealer immediately. EXTERNAL POWER SUPPLY When using the Incubator T20 stand-alone model, at delivery the plug of the AC-adapter is correctly combined: The plus terminal is located inside the head of the plug. + The plug has to be put into the...

Open the catalog to page 6
Incubator T20 - 7

INSTALLATION Connect the AC-adapter to the mains. The operating voltage is 100 VAC up to 240 VAC at 50/60 Hz. Or connect the Incubator T20 directly to the photometer while the photometer is OFF. After some seconds the green LED is flashing. The red LED shows a continuous light. ROBERT RIELE GmbH & Co KG

Open the catalog to page 7
Incubator T20 - 8

FRONT INCUBATOR T20 4 tubes 16 normal standard cuvettes Sample holder for tubes with  13mm Plug to connect to photometer 3.2 ROBERT RIELE GmbH & Co KG

Open the catalog to page 8
Incubator T20 - 9

After switching ON the device the Incubator T20 heats up to a temperature of 37 °C. The device needs about 20 minutes for warming up. After the warming up time the GREEN LED shows a continuous light. At this state the system is ready for use. The status of the device is shown by two LEDs (Light Emitting Diode): GREEN LED (used for stability control)  The LED is flashing:  The LED shows a continuous light: RED LED (used for heating power)  The LED is flashing:  The LED shows a continuous light: The heating is switched on during heating up. ROBERT RIELE GmbH & Co KG

Open the catalog to page 9
Incubator T20 - 10

MAINTENANCE This chapter provides necessary information concerning general maintenance by the user. If any faults should occur which cannot be remedied, then service should be contacted. Repairs at the device may be carried out only by authorized specialist staff. Through improper repairs the warranty extinguishes, and the user can be heavily jeopardized. CLEANING INSTRUCTION Liquid waste is potentially biologically hazardous. Always wear gloves if handling those materials. Do not touch parts of the device other than those specified. Consult the laboratory protocol for handling biohazardous...

Open the catalog to page 10
Incubator T20 - 11

TECHNICAL DATA ENVIRONMENTAL CONDITIONS Climatic conditions for storage and transport of the packed device:  Temperature: -25 °C to +70 °C  Relative humidity: 20 % to 85 % The device must be used in an environment that meets the following conditions:  Temperature: +15 °C to +35 °C  Relative humidity: 20 % to 85 %  Not exposition to direct sunlight or other source of direct thermal radiation  Well-ventilated area  Free from excessive dust  Free from combustible gasses  Free from vibrations  Free from electromagnetic wave interference  Well-distanced from a machine generating a...

Open the catalog to page 11
Incubator T20 - 12

SHORT SPECIFICATION MEASURING SYSTEM  Microcontroller based temperature unit  POWER SUPPLY  Supply voltage: Supply current maximal: Power consumption: External mains adapter Output: Input: Driving with 12 VDC (car-)battery is possible ROBERT RIELE GmbH & Co KG

Open the catalog to page 12

All ROBERT RIELE catalogs and technical brochures