Vertica" Pendant Arms and Enclosures Vertically Adjustable Mountings for Operator Interfaces Adjustable Height for each operator. Automatically Locks in Place when repositioned vertically. Convenient Grab Handle unlocks and automatically relocks vertical position. 13", 23", or 30" of vertical adjustment. Internal Cable Passageway sealed and safe. Versatile Mounting Styles for any plant floor location: Wall Mount Post Top Machine Top Arm Extensions include: Horizontal Extension Middle Joint Extension Rigid Wall Mount Extension Vertical Extension Counterbalances up to 100 lbs. Precision-sized Enclosures for any operator interface. Available from Stock in every configuration. Custom Colors and finishes available. Also Available in NEMA 4X Stainless Steel Vertica arms and enclosures are available for corrosive, sanitary and washdown applications. 425 Caredean Drive • Horsham, PA 19044 • Phone 215.443.3400 • Fax 215.443.3002 ©2005 STRONGARM, Inc. STRONGARM and the STRONGARM logo are registered trademarks of STRONGARM, Inc. All other trademarks are the property of their respective owners.

Access cover to Cable Passage Vertical Adjustment with Automatic Lock-in-Place and Gas Spring Counterbalance Choice of Mounting Post Top Wall Mount (shown) » Vertical Ranges up to 30" MSC™' I Instant Adjustability I 100% Counterbalanced I Locks-in-Place Automatically I Sealed Cable Passageway Industrial Strength Swivel with stop Gasketed Mounting Surface Heavy-duty, cast aluminum construction makes the Vertica arm ideal for mounting flat panel operator interfaces in demanding plant floor environments. Versatile mounting designs allow the Vertica arm to be attached to any horizontal or vertical...

Vertica Pendant Arms ™ Vertica Selection and Articulation Vertica – 13" of Vertical Adjustability Typical Application For ergonomic height adjustment of the display which eliminates the nearly impossible engineering task of mounting the display at “just the right height” to please everyone. Swivel 22.3" Top of Travel/Horizontal (15.7" Bottom of Travel) 6.2" (159) 45˚ See Surface Mounting Styles Enclosure Mounting Surface Vertica L – 23" of Vertical Adjustability Typical Application 22.3" Top of Travel/Horizontal Set-up and monitoringBottom of Travel)interface is pulled down for machine (15.7"...

Vertica Pendant Arms ™ Surface Mounting Selection Wall Mount A Wall Mount Vertica Arm attaches to a vertical surface with a thru-hole pattern (4) 0.53 ∅. Cables enter through the center of mounting surface or female 2½" NPT access cap opening. Rotational stops at 180° (±90°) are standard; alternate stops can be specified. Cabling access opening (2½" NPT) can be used as Alternate Cable Entry. ½", ¾", or 1" NPT adapter caps available as options. Blind Wall Mount The blind wall mount is simply the wall mount with the thru-hole mounting plate removed. Typically used for a cleaner look on OEM equipment....

Vertica Pendant Arms ™ Assembly Configuration Selection Standard Configuration The mounting surface supports the arm and the enclosure is suspended from the arm. This is the most popular configuration. Inverted Configuration The mounting end is inverted, resulting in the arm being suspended from the mounting surface. Inverted post-mounted arms are popular for supporting the arm from the ceiling. Supported Configuration The mounting surface is supporting the arm and the enclosure is supported by the arm. A vertical extension is required for this configuration so that the arm does not come in contact...

Vertica Pendant Arms ™ Horizontal Extension The horizontal extension increases the overall length of the arm. The horizontal extension is inserted between the mounting surface pivot and the Vertica arm. Vertical travel does not change. Swivelto-swivel length is increased by dimension "L". Middle Joint Extension The middle joint extension adds a third pivot to the Vertica arm for in/out adjustability. Optional Stacked Middle Joint Configuration

Vertica Pendant Arms ™ Arm Extensions (continued) Rigid Wall Mount Typically used when there is a mounting surface available but not in the ideal location. The rigid wall mount essentially moves the mounting surface. Both length and angle can be specified. These extensions are preferable over horizontal and middle joint extensions for applications that require a long reach. 6.0" 5.3" (Cable Entry 4.75" through Mounting Surface or optional conduit coupling) (Cable Entry 4.75" through Mounting Surface or optional conduit coupling) Ø 0.53" holes for ½" bolts (4) Places Vertical Extension 4.75" (Cable...

Vertica Pendant Arms ™ Vertica Options Floorpost For use with a post top mount Vertica arm, the floorpost is a very popular method of mounting an arm when a structural surface is not available. The 74" post is for Vertica arms and the 79" post is for Vertica arms with a middle joint extension. Fabricated from heavy wall 3½" structural tube welded to a 12" x 12" x 3/8" thick baseplate. A 1½” female NPT coupling near the base for cable entry, additional couplings can be specified or located differently. (79" used for Middle Joint (79" used for Middle Jointextension) extension) 1½" NPT Ø 0.56" for...

Vertica Options (continued)

Operator Interface Enclosures Perfectly-sized Enclosures Set-up and Ready to Install Full size rear access door Reinforced for Pendant mounting Side doors for cable and drive access as required Clean, seam-welded construction Lift-off Door Hinges Accurately sized and cut out for the operator interface ndividually sized for the exact model of operator interface. I houghtful consideration of engineering details. T   onvenient side access doors for cabling and drives. C   quare and precise laser cut and TIG welded construction. S   eadily available custom finishes include both paint and powder coat....