Electronic Pressure Switches sehctiwS erusserP cinortcelE 96

Mating plugs, thread adapters and programming devices High-quality accessories Developed for our products Aligned to our products Direct from the manufac

Mating plugs For requirements at short notice and realising customized solutions TE AMP Superseal 1.5®, 3-pin 3 x 0,5 mm² Radox Kabel (2 m), IP65 M12x1 DIN EN 61071-2-101 D straight, 4-pin Terminals for wire diameter 0.75 mm² (AWG 18) Suitable for connector code 010 Deutsch DT04-3P Suitable for connector code 007 AMP Superseal 1.5® Suitable for connector code 002 M12 DIN EN 61076-2-101 A Suitable for connector code 002 M12 DIN EN 61076-2-101 A Order number: 1-1-00-653-162 Hex thread ring (tightening torque: 0,6 Nm) Coupler socket M12x1 DIN EN 61071-2-101 D angled, 4-pin Terminals for wire diameter...

Thread adapters For requirements at short notice and realising customized solutions The materials and shapes of thread adapters are aligned perfectly to our electronic pressure switches and transmitters Thread adapters are provided together with seals to ensure safe and easy installation of our electronic pressure switches and transmitters For G 1/4 DIN EN ISO 1179-1 (DIN 3852-E) SUCO thread code 41, transmitters and electronic pressure switches Stainless steel 1.4305 / AISI 303 thread adapters G 1/4 DIN EN ISO 1179-1 (DIN 3852-E) female thread incl. sealing ring FKM Order number: Order number:...

for electronic pressure switches of the SUCO „Performance“ series easy and quick adjustment of technical parameters onsite individual programming of the switching points and the switch delay time (0 . . . 2 s) selectable between hysteresis and window function Programming device PPD05 Plastic case USER MANUAL User manual USB-Stick with programming software 1) USB cable M12x1; DIN EN 61076-2-101-A Basic set with M12 connector Additional connectors can be retrofitted. M12x1 AMP Superseal Plastic case USER MANUAL User manual USB-Stick with programming software1) Complete set with all available connectors...

Technical explanations for electronic pressure switches What is an electronic pressure switch? An electronic pressure switch converts the medium pressure which is present at the measuring cell into a digital, electrical switch signal (ON / OFF). An electronic pressure switch is more complex than a mechanical pressure switch, and thus generally more expensive. As an electronic pressure switch has no moving parts (relative to each other), it usually has a much prolonged service life and provides a higher level of precision (depending on application). The hysteresis can be set over a wide range...

Adjustment range of switching point The pressure range within which the switching point of an electronic pressure switch can be set is called adjustment range. The switching point corresponds to the pressure value at which the electric circuit of the output is opened or closed. Window function In the window function, the switch signal is programmed such that it remains ON or OFF between two values. This means a defined pressure range can be monitored. This function is only possible on the 053X series. pressure profile Hysteresis Rising/falling switching point The difference between the rising (upper)...

Technical explanations for electronic pressure switches PNP output / high-side / plus-switching PNP output (plus-switching) is the most popular variant in Europe. Here the load is connected to the output of the switch and ground (GND as reference potential). NPN output / low-side / minus-switching For an NPN output (minus-switching), the load is connected to the switching output and to the positive line of the supply voltage (Uv+ as reference potential). Temperature errors and ranges The temperature (both of the medium and environment) generally has a signicant influence on the accuracy of an...

Sampling rate The sampling rate (or sampling frequency) defines the number of samples per time unit (typically in seconds or milliseconds) taken from an analogue signal and converted to a digital signal. The sampling rate is an indicator of how fast the output signal of an electronic pressure switch responds to the pressure change at the input. CE mark Electronic pressure switches from SUCO fall under the 2014/30/EU EMC Directive. EC declarations of conformity have been issued for the electronic pressure switches are available on request or can be downloaded from our website. The relevant devices...

Technical explanations for electronic pressure switches Conversion chart for pressure units Insulation strength According to the latest specifications for immunity to surges and lightning protection, the following must be taken into account when testing insulation strength: With insulation test devices having an inner resistance exceeding 42 Ohm, the insulation strength of electronic pressure switches can be tested up to 500 VDC. All contacts must be tested short-circuited against the housing. For a specific threshold value of test voltage, the protective circuit for surge protection is activated...

General technical explanations User information Our pressure monitoring products may only be installed and started up by authorised specialists. The safety regulations of country-specific authorities must be observed, especially when working with mains voltages and oxygen, and in potentially explosive areas. Product information The technical information in this catalogue is based upon fundamental testing during product development and empirical values. The information cannot be used for all application scenarios. Testing of the suitability of our products for a specific application (such as the checking...

RoHSII compliant Values 30% lower than in the table above must be used for brass housings. Gaseous applications In particular using additional sealant to attain the required leak tightness may be necessary for gas applications. Vacuum The values given in the technical details for the vacuum range are specified in millibars (mbar) below atmospheric pressure. Pressure change rate (~rise / ~fall) The pressure change rate denotes the pressure over time for the rising/falling pressure. The pressure change rate is specified in bar/s or bar/ms. The maximum pressure change rate for SUCO mechanical pressure...