Thermo Scientific Multifuge X1 Multifuge X1R Instructions for Use 50120964-g • 06 / 2020 Visit us online to register your warranty:

WEEE Conformity This product is subject to the regulations of the EU Waste Electrical & Electronic Equipment (WEEE) Directive 2012/19/EU. It is marked by the following symbol:

Thermo Scientific

Thermo Scientific

P Preface Before starting to use the centrifuge, read through this instruction manual carefully and follow the instructions. The information contained in this instruction manual is the property of Thermo Fisher Scientific; it is forbidden to copy or pass on this information without explicit approval. Failure to follow the instructions and safety information in this instruction manual will result in the expiration of the sellers warranty. Scope of Supply Article Number Quantity Centrifuge Multifuge X1 Power supply cable Instruction manual If any parts are missing, please contact your nearest Thermo...

Accident Prevention Prerequisite for the safe operation of the Multifuge X1 / X1R is a work environment in compliance with standards, directives and trade association safety regulations and proper instruction of the user. The safety regulations contain the following basic recommendations: • Maintain a radius of at least 30 cm around the centrifuge. • Implementation of special measures which ensure that no one can approach the centrifuge for longer than absolutely necessary while it is running. • The mains plug must be freely accessible at all times. Pull out the power supply plug or disconnect...

• The lid emergency release may be used in emergencies only to recover the samples from the centrifuge, e.g. during a power failure (see section “Mechanical Emergency Door Release” on page 7-2). • Never use the centrifuge if parts of its cover panels are damaged or missing. • Do not touch the electronic components of the centrifuge or alter any electronic or mechanical components. • Please observe the safety instructions. Please pay particular attention to the following aspects: • Location: well-ventilated environment, set-up on a level and rigid surface with adequate load-bearing capacity. •...

This symbol refers to general hazards. CAUTION means that material damage could occur. WARNING means that injuries or material damage or contamination could occur. This symbol refers to biological hazards. Observe the information contained in the instruction manual to keep yourself and your environment safe. Thermo Scientific

1 Introduction and Description Contents • “Characteristics of the Multifuge X1 / X1R” on page 1-2 • “Technical Data” on page 1-3 • “Directives, Standards and Guidelines” on page 1-4 • “Functions and Features” on page 1-5 • “Mains Supply” on page 1-5 • “Rotor Selection” on page 1-6

Introduction and Description Characteristics of the Multifuge X1 / X1R Characteristics of the Multifuge X1 / X1R The Multifuge X1 / X1R is an in-vitro diagnostics device according to the In-Vitro Diagnostics Directive 98/79/EC. Several rotors with a wide range of tubes can be used. The set speed is reached within seconds. The maintenance-free induction motor ensures quiet and low-vibration operation even at high speeds, and guarantees a very long lifetime. The user-friendly control panel makes it easy to pre-set the speed, RCF value, running time, temperature, and running profile (acceleration...

Introduction and Description Technical Data Technical Data The technical data of the Multifuge X1 / X1R is listed in the following table. Table 1-1. Technical Data Multifuge X1 / X1R Feature Environmental conditions -Use in interior spaces -Altitudes of up to 2,000 m above sea level -max. relative humidity 80 % up to 31 °C; decreasing linearly up to 50 % relative humidity at 40 °C. permissible ambient temperature Overvoltage category Pollution degree Heat dissipation running time maximum RCF value at nmax maximum kinetic energy noise level at maximum speed temperature setting range Height Height...

Introduction and Description Directives, Standards and Guidelines Directives, Standards and Guidelines Table 1-3. Directives, Standards and Guidelines Region 98/79/EC In Vitro Diagnostics 2011/65/EU RoHS Directive on the Restriction of the use of certain Hazardous Substances in electrical and electronic equipment Protective golas of: 2006/42/EC Machinery 2014/35/EU Low Voltage 2014/30/EU Electromagnetic Compatibility (EMC) Product code JQC centrifuges for clinical use Device class 1 Emitted interference FCC Part 15 CLASS A NOTE: This equipment has been tested and found to comply with the limits...

Introduction and Description Functions and Features Functions and Features The following table gives an overview of the important functional and performance characteristicsof the Multifuge X1 / X1R. Table 1-4. Functions and Features Component / Function Description / Features Structure / Housing Galvanized steel chassis with armored plating Stainless steel Induction drive without carbon brushes Easy-to-clean keypad and display surface Internal memory The most recent data is saved RCF-selection, temperature control, pretemp with cooling equipped devices Acceleration / braking profiles 9 acceleration...

Introduction and Description Rotor Selection Rotor Selection The Multifuge X1 / X1R is supplied without a rotor. Various rotors are available to choose from. TX-400 75003629 with round buckets TX-200 with round buckets BIOShield The technical data of the rotors and the corresponding adapters and reduction sleeves for various commercially available containers can be found in the corresponding rotor operating manuals. For more information visit our website at: http://www.thermofisher.com Thermo Scientific

• “Before Setting up” on page 2-2 • “Transporting the Centrifuge” on page 2-2 • “Location” on page 2-2 • “Aligning the Centrifuge” on page 2-3 • “Mains Connection” on page 2-3 • “Storage” on page 2-4