User Manual Series 8000DH CO2 Incubator Direct Heat with Sterilization Cycle Operating and Maintenance Manual 7013540 Rev. 6 Visit us online to register your warranty www.thermoscientific.com/labwarranty

*T/C is a thermal conductivity sensor. IR is an infra-red sensor. **All units are 50/60 Hz. Changed label in remote alarm artwork to note - pg 6-1 Added risk assessment information New magnetic door switch (parts list, expl dwg, elec schematics) RoHS Updated solenoid - pgs 8-5 & 9-1 through 9-3 Added SRO ext door part number 1900567 to parts list CO2 valve connection inlet & inner door switch kits-parts list & drawing 370-200-5 ccs Thermo Scientific Release level 2 - added spring rod kit (pg. 1-7) Direct Heat CO2 Incubator

CAUTION Contains Parts and Assemblies Susceptible to Damage by Electrostatic Discharge (ESD) Important Read this instruction manual. Failure to read, understand and follow the instructions in this manual may result in damage to the unit, injury to operating personnel, and poor equipment performance. s Caution All internal adjustments and maintenance must be performed by qualified service personnel. s • Use this product only in the way described in the product literature and in this manual. Before using it, verify that this product is suitable for the intended use. Do not modify system components,...

Important operating and/or maintenance instructions. Read the accompanying text carefully. Potential electrical hazards. Only qualified persons should perform procedures associated with this symbol. Equipment being maintained or serviced must be turned off and locked off to prevent possible injury. Asphyxiation Hazard Warning. High concentrations of CO2 and N2 can displace oxygen and cause asphyxiation! Lifting Hazard Warning. The incubator weighs more than 200lbs (91kgs). Take adequate safety measures when moving this device. WEEE Compliance: Thermo Fisher Scientific has contracted with companies...

Do You Need Information or Assistance on Thermo Scientific Products? If you do, please contact us 8:00 a.m. to 6:00 p.m. (Eastern Time) at: 1-740-373-4763 1-800-438-4851 1-877-213-8051 http://www.thermoscientific.com [email protected] www.unitylabservices.com Direct Toll Free, U.S. and Canada FAX Internet Worldwide Web Home Page Tech Support Email Address Certified Service Web Page Our Sales Support staff can provide information on pricing and give you quotations. We can take your order and provide delivery information on major equipment items or make arrangements to have...

Warranty Notes Information You Should Know Before Requesting Warranty Service • Locate the model and serial numbers. A serial tag is located on the unit itself. • For equipment service or maintenance, or with technical or special application inquiries, contact your local distributor. Repairs NOT Covered Under Warranty • Calibration of control parameters. Nominal calibrations are performed at the factory; typically ±1°C for temperature, ±1% for gases, and ±5% for humidity. Our service personnel can provide precise calibrations as a billable service at your location. Calibration after a warranty...

Table of Contents Section 1 Direct Heat CO2 Incubator Installation and Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 Keypad Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3 Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4 Installing the Incubator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4 Stacking the Incubators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5 Preliminary Cleaning . . . . . . . . . . . . . . ....

Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 Sensor Fault Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2 Temp Controller Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2 TMP CNTR ERR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2 Thermo Scientific Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1 Turn Audible Alarm ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . ....

Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1 Exploded Part Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2 Factory Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1 Remote Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1 Humidity Readout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2 Direct Heat CO2 Incubator Thermo Scientific

Chamber Gas Sample Port Control Panel Power Switch Steri Cycle Sterilization Cycle Button See Section 1 Inner Door Leveling Legs (4) Door Heater Cable Chamber Gas Sample Port - Used for sampling chamber CO2 content using a FYRITE or similar instrument. Main Power Switch - Mains Disconnect Control Panel - Keypad, displays & indicators (Figure 1-2) Leveling Legs - Used to level the unit Sterilization Cycle Button - Switch to initiate sterilization cycle Note The incubators are stackable. Information follows. s Thermo Scientific Direct Heat CO2 Incubat

Section 1 Installation and Start-Up - Silences the audible alarm. See Section 4 for alarm ringback times. Alarm Indicator - Light pulses on/off during an alarm condition. MODE Select Switch - Used to select Run, Setpoints, Calibration and Configuration modes. Mode Select Indicators RUN: Run Menu SET: Set Points Menu CAL: Calibration Menu CON: Configuration Menu Message Display - Shows system status. HEAT Indicator - Lights when heaters are activated. INJ Indicator - Lights during CO2 injection into chamber. T (°C) Display - Programmable to display temperature. See Configuration section. RH (%)...