TiMOTION's JP3 series inline linear actuator was designed for low load industrial applications where up to IP69K dust and liquid ingress protection is necessary. It is best suited for applications with visual or compact installation dimension requirements. Hall sensors are optional for the JP3 which allow for synchronization and position feedback. General Features Voltage of motor Maximum load Maximum speed at full load Stroke Minimum installation dimension IP rating Color Certificate Operational temperature range Operational temperature range at full performance Storage temperature range An inline actuator designed for small spaces 12V DC, 24V DC, or 24V 2,000N in push / pull 19mm/s (with 500N in a condition) 2 0~1 0 00mm > Stroke + 217mm Up to IP69K Black or grey UL73 -5°C~+65°C +5°C~+45°C -40°C~+70°C

Drawing Standard Dimensions (mm) 0IO.2 Load and Speed CODE Load (N) Push Pull Self Locking Force (N) Typical Current (A) No Load With Load Typical Speed (mm/s) No Load With Load Note 1 Please refer to the approved drawing for the final authentic value. 2 Standard stroke: Min. > 20mm, Max. please refer to below table 3 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 4 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately...

Motor Speed (5600RPM, Duty Cycle 10%) Speed vs. Load Performance Data (24V DC Motor) Note 1  The performance data in the curve charts shows theoretical value.

1 = Aluminum casting, U clevis, slot 4.2, depth 18.0, hole 10.2 1 = Aluminum casting, no slot, hole 6.4 2 = Aluminum casting, no slot, hole 8.0 3 = Aluminum CNC, U clevis, slot 6.0, depth 13.0, hole 10.0 4 = Aluminum CNC, U clevis, slot 6.0, depth 13.0, hole 6.4 5 = Aluminum CNC, U clevis, slot 6.0, depth 13.0, hole 8.0 6 = Aluminum casting, hole 10.0 1 = Two switches at full retracted / extended positions to cut current 2 = Two switches at full retracted / extended positions to cut current + 3rd LS to send signal 3 = Two switches at full retracted / extended positions to send signal 4 = Two...

Retracted Length (mm) 1. Calculate A+B + C = Y 2. Retracted length needs to > Stroke + Y A. Front Attachment C. Output Signal

JP3 Ordering Key Appendix Rear Attachment (mm) 1 = luminum casting, U clevis, slot A 4.2, depth 18.0, hole 10.2 11.7 Front Attachment (mm) 3 = luminum CNC, U clevis, slot 6.0, A depth 13.0, hole 10.0 5 = luminum CNC, U clevis, slot 6.0, A depth 13.0, hole 8.0 ø8 4 = luminum CNC, U clevis, slot 6.0, A depth 13.0, hole 6.4 2 = luminum casting, no slot, hole A 8.0 1 = luminum casting, no slot, hole A 6.4 6 = Aluminum casting, hole 10.0 9 Direction of Rear Attachment (Counterclockwise)

JP3 Ordering Key AppendixFunctions for Limit Switches Wire Definitions CODE Pin 1 (Green) 2 (Red) O 3 (White) 4 (Black) 5 (Yellow) A (Blue) 1 extend (VDC+) N/A N/A N/A retract (VDC+) N/A 2 extend (VDC+) N/A middle switch pin B middle switch pin A retract (VDC+) N/A 3 extend (VDC+) common upper limit switch N/A retract (VDC+) lower limit switch 4 extend (VDC+) common upper limit switch medium limit switch retract (VDC+) lower limit switch 1 = DIN 6P, 90° plug 2 = Tinned leads Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION...