Product Segments • Industrial Motion TiMOTION's JP3 series inline linear actuator was designed for low load industrial applications where up to IP69K (static) dust and liquid ingress protection is necessary. It is best suited for applications with visual or compact installation dimension requirements. Hall sensors are optional for the JP3 which allow for synchronization and position feedback. The JP3 offers stroke lengths from 20 to 1000mm and delivers up to 2,000N of force, making it ideal for compact systems requiring moderate push or pull performance. With speeds up to 23.5mm/s at no load, and UL73 certification, this IP69K linear actuator ensures both efficiency and compliance. Operating within -5°C to +65°C, JP3 is ideally for mobile equipment and agricultural machinery, where compactness and outdoor durability are essential. General Features Max. load Retracted length Output signals NPN Hall sensor (5~36V input) * 2 Black, grey Operational temperature range Operational temperature range at full performance Storage temperature range

Drawing Standard Dimensions (mm) Load and Speed CODE Load (N) Self Typical Current (A) Typical Speed (mm/s)Typical Current (A) Typical Speed (mm/s) Push Pull L°ckin(9N) No Load With Load No Load With Load No Load With Load No Load With Load Motor Speed (5600RPM, Duty Cycle 10%) 1 Please refer to the approved drawing for the final authentic value. 2 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. The self-locking force is a minimum value and can be actually higher. 3 The current...

Motor Speed (5600RPM, Duty Cycle 10%) Speed vs. Load 25.0 Performance Data (24V DC Motor)

Performance Data (12V DC Motor) Motor Speed (5600RPM, Duty Cycle 10%)

Retracted Length (mm) See page 6 Rear Attachment (mm) See page 7 Direction of Rear Attachment (Counterclockwise) 1 = Aluminum, U clevis, slot 4.2, depth 18.0, hole 10.2 1 = Aluminum, slotless, hole 6.4 4 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 6.4 2 = Aluminum, slotless, hole 8.0 5 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 8.0 3 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 10.0 6 = Aluminum, hole 10.0 Special Function of Spindle Subassembly Output Signal 1 = Two micro switches cut off the actuator at end of stroke 2 = Two micro switches cut off the actuator at end of stroke...

2. Retracted length needs to > Stroke + Y A. Front Attachment C. Output Signal

JP3 Ordering Key Appendix Rear Attachment (mm) 1 = Aluminum, U clevis, slot 4.2, depth 18.0, hole 10.2 11.7 Front Attachment (mm) 2 = Aluminum, slotless, hole 8.0 9 5 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 8.0 ø8 4 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 6.4 3 = Aluminum, U clevis, slot 6.0, depth 13.0, hole 10.0 1 = Aluminum, slotless, hole 6.4

Connector 2 = Tinned leads PTC outside the motor; at cable length 100mm, min total cable = 250mm

qo t moTion Wire Definition Port Functions for Limit Wire Color Number Switches Position Feedback 0. Without A1 Two micro switches cut off the actuator at end of stroke Two micro switches cut off the actuator at end of stroke + third one in between sends signal Two micro switches send signal at end of stroke Two micro switches send signal at end of stroke + third one in between sends signal 2,N. Hall Sensor*2 EXT+ RET+ Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice....