TGM2 Series
7Pages

{{requestButtons}}

Catalog excerpts

TGM2 Series - 1

series Product Segments • Ergo Motion • Industrial Motion The TGM2 series is TiMOTION's most powerful gear motor. It was designed primarily for ergonomic applications like height adjustable workstations and tables, but can be used in many other applications. This economical product allows for fast, smooth and quiet adjustment of built-in spindles through the use of external limit switches. Shafting allows for the mechanical synchronization of dual spindles. General Features Voltage of motor Maximum speed at full load Maximum rated torque Operational temperature range at full performance Options Hexagon hole for the shaft by 9mm diameter Low noise 24V DC, thermal protector 51RPM (±5%) after gear reduction 18.3Nm +5°C~+45°C Hall sensors

Open the catalog to page 1
TGM2 Series - 2

Drawing Standard Dimensions -Without TES2 (mm) Standard Dimensions -With TES2 Load and SpeedCODE Torque Load (Nm) Self Locking Force (Nm) Typical Current (A) Typical Speed Hall Sensor Output No Load With Load No Load With Load Magnet Period (ms) No Load With Load Note 1 Please refer to the approved drawing for the final authentic value. 2 The current & speed in table and diagram are tested with TiMOTION control boxes, and there will be around 10% tolerance depending on different models of the control box. (Under no load condition, the voltage is around 32V DC. At rated load, the voltage...

Open the catalog to page 2
TGM2 Series - 3

Motor Speed (3800RPM) Speed vs. Torque Load 400 Current vs. Torque Load A Performance Data (24V DC Motor)

Open the catalog to page 3
TGM2 Series - 4

Performance Data (24V DC Motor) Speed vs. Torque Load Current vs. Torque Load

Open the catalog to page 4
TGM2 Series - 5

Voltage 5 = 24V, thermal protector Load and Speed See page 2 Output Signal 0 = Without 2 = Hall sensor * 2 Brake 0 = Without 1 = Motor brake Plug See page 6 Cable Length (mm) 0 = Tinned leads 1 = DIN 6P, 90° 2 = Molex 8P 0 = Straight, 1000 1 = Straight, 1500 2 = Straight, 2000 3 = Curly, 1000 Output Torque See page 6 External Limit Switch (TES2) 1 = Drive shaft hole (inner hexagon 9mm) 4 = Two sides drive shaft 2 = One side drive shaft (012mm, knurling) (012mm, with 048mm latch hole> 3 = Two sides drive shaft (012mm, knurling) 5 = Drive shaft hole (inner hexagon 6mm) 00 = Without XX =...

Open the catalog to page 5
TGM2 Series - 6

TGM2 Ordering Key Appendix Plug 0 = Tinned leads Output Torque 1 = Drive shaft hole (inner hexagon 9mm) 2 = One side drive shaft (Ø12mm, knurling) 12 3 = Two sides drive shaft (Ø12mm, knurling) 4 = wo sides drive shaft (Ø12mm, with Ø4.8mm latch hole) T ø4.8 5 = Drive shaft hole (inner hexagon 6mm)

Open the catalog to page 6
TGM2 Series - 7

qo t moTion TBS Series - the combination of TGM and TBS Note 1 The combinations of TGM and TBS are marked as "v" on the above table. 2 When choosing the combination of TBS2 / 3 and TGM7, the hexagonal drive shaft is not required. 3 When choosing the combination of TBS1 / 4 / 5 / 9 / 10 and TGM1 / 3 / 4, the extra order of hexagonal drive shaft is needed. 4 Please refer to the table below for the serial numbers and the dimensions of the component. Hexagonal drive shaft The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products...

Open the catalog to page 7

All TiMOTION Technology catalogs and technical brochures

  1. ERGO MOTION

    48 Pages

  2. CARE MOTION

    32 Pages

  3. series TL3

    12 Pages

  4. JP4 series

    7 Pages

  5. TA41 series

    11 Pages

  6. JP3 series

    7 Pages

  7. TA6 Series

    10 Pages

  8. TA1 Series

    12 Pages

  9. TGM3 Series

    6 Pages

  10. TGM1 series

    7 Pages